Maximum flow ranges from Max pressure Temperature range UNIVERSAL Flow Monitors ® Vortex Shedding Flowmeter CoolPoint™ with Rotatable Enclosure option User-Configurable Options Features that are selectable on the 3 wire standard 4-20 mA units include: • Selectable alarm state (N.O. or N.C.) • Set point or pulse output • Engineering units (GPM, LPM) This flowmeter is made for water, water/glycol coolant of low viscosity fluids. There are no moving parts to clog or wear. They are certified CSA and CE. They have a 4-20 mA output. There are two versions. The three wire version (power supplied separate from the 4-20) has a solid state relay that can be configured as an alarm or as a pulse out. It has a bright LED digital display of flow rate. The two wire version (option E14) has no display, pulse out or alarm point. It can be operated in an intrinsically safe mode only when used in conjunction with an approved intrinsic safety barrier meeting required entity parameters. Instrument Specifications • Flow Visual readout: 3 digit LED, 0.3" digit height. Deadband for Alarm: 5% of full scale (maximum flow) 3 wire units only. Accuracy: ±2% of full scale (maximum flow). Repeatability: ±.25% of indicated flow. Turndown (ratio of max to minimum flow rates): 10:1 at all temperatures and 20:1 available optionally for standard temperatures. • Pressure 300 PSIG (20 Bar) operating pressure • Response time 450 ms. • General Fluid temperature limits: 35-150° F (2-66° C) standard, 150-210° F (66-99° C) optional 3 wire units only. Enclosure rating: IP 65, Type 1, 3, 4, 12 and 13 • Pipe Connections: Female NPT, BSPP & BSPT • Back pressure of 10 PSIG required Electrical Specifications • Input Power: 10 - 30 VDC @ 80 mA standard, 25 mA for the 2 wire option • Output: 4-20mA for flow • 100 pulses per gallon from the solid state relay for 3 wire (standard) option – all units except the 2 inch CP16 which is 25 pulses per gallon • Electrical Connection Pin Connector (standard) Pigtails (optional) Junction Box with terminal strip (optional) Material Specifications Flow bodies of brass or 316 Stainless Steel with PVDF sensors and Viton® seals standard. PEEK sensors used for high temp for fluids above 150° F. Viton® is a registered trademark for DuPont Performance Elastomers. CP-CNMed091412

Select the appropriate symbols to build a model code: Special options W1=20:1 extended turndown*** E20=High temp (150-210° F)**** Available with CN units only: E14 = 2wire 4-20 mA looppowered transmitter. No alarms, display or high temp available with this option. NOTE: E14 option can be operated in an intrinsically safe mode only when used in conjunction with an approved instrinsic safety barrier meeting required entity parameters. 8140R-ASSY = Optional approved barrier * Indicates default selection. If no selection is made, this option is assumed. *** Requires grounded wiring, standard temp...

Installation Drawing – Basic Meters A Installation Drawing – Meters with Optional Junction Box A

ACCESSORy CablES Available for Pin Connector Meters Series Description Length in Part Meters Number CP/CN 5 pin 1 6241-1M female 3 6241-3M 10 6241-10M Barrier used for 2 wire option where Intrinsic Safety is required. Part number: 8140-ASSY CP 3 wire standard units WHITE +24 Vdc SUPPLY FLOW RELAY CONTACT BLACK BLUE To turn flow relay contact from a switch to a pulse out by externally connecting a 2K - 10K Ohm pull up resistor from power supply to one flow relay contact and connecting the other flow relay contact to supply ground. FLOW RELAY CONTACT SUPPLY GROUND configuration: • 1: + 24 VDC power...