HX-P510 SERIES
4Pages

0 to 5, 0 to 10, ±5, ±10 VDC ANALOG OUTPUT The UniMeasure HX-P510 Series transducer offers a voltage output with wide adjustability to give a 0 to 5, 0 to 10, ±5 or ±10 VDC output. The device may be powered with an unregulated voltage in the range of 4.9 to 30 VDC. Zero and span adjustment potentiometers are readily accessible. With the zero position set anywhere within the first 30% of total travel, the span may be adjusted to give a full 0 to 5 or 0 to 10 VDC output with the span set anywhere within the last 20% of travel. Alternatively, the zero position may be set anywhere between 10% and 90% of full travel to give an output of ±5 or ±10 VDC with the span set between 50% to 100% of the longest travel from the zero position. FOOTNOTES TO SPECIFICATIONS 1. Supplemental Data section located at end of HX Series pages. 2. Submersion to 2m (6.5’) maximum depth in fresh water. MODEL NUMBER CONFIGURATION Basic Configuration RANGE Select Measurement Range From S u p p l e m e n t a l D a t a , Ta b l e 12 Table 12 (next page), Insert Corresponding Measurement Range Designator (See Supplemental Data, Table 12) INGRESS PROTECTION Nylon Jacketed Stainless Steel Ranges to 80” (2m) only. (formerly NJC) WIRE ROPE TENSION WIRE ROPE EXIT DIRECTION Use Number designators shown NOTES FOR OPTION BOXES (NEMA 4): Transducer equipped with body mounted connector and with or without mating connector. Mating connector with electrical cable available separately as part number 10119-xM where ‘x’ is length of electrical cable in meters. IP-68–NEMA 6 CABLE MOUNTED CONNECTOR (NEMA 6): Transducer equipped with bulkhead fitting and length of electrical cable. Remote end of electrical cable may be outfitted with water proof connector. Mating connector with electrical cable available separately as part number 10424-xM where ‘x’ is length of electrical cable in meters. 4175 SW Research Way, Corvallis, Oregon 97333 U.S.A

TYPICAL HX MOUNTING BOLTS Use value from this column to indicate overall measurement range MEASUREMENT RANGE DESIGNATOR STANDARD MEASUREMENT RANGES Check mark indicates available measurement range APPLICABLE SERIES HX-PA HX-PB HX-P420 HX-P510 NOTES: 1. With 1K ohm potentiometer, wire rope misalignment 2° maximum at full stroke, relatively dust free environment, nylon jacketed wire rope on units with ranges 80” and less. WIRE ROPE TENSION (NOMINAL) (oz) WIRE ROPE DIAMETER (in) TRANSDUCER WEIGHT Product Photo 7.2 7.4 Specifications subject to change without notice 4175 SW Research Way,...

SUPPLEMENTAL DATA OPTION DESCRIPTIONS OPTION OPTION DESIGNATOR NYLON JACKETED WIRE ROPE RANGES TO 80” ONLY NYLON JACKETED WIRE ROPE RANGES 100" TO 500" ONLY ALTERNATE WIRE ROPE EXIT RANGES TO 80” (2.0 m) DESCRIPTION Replaces standard stainless steel wire rope with Ø.018 nylon jacketed wire rope. This option increases wire rope life dramatically but may increase non-linearity by as much as ±.05% of full scale. Replaces standard stainless steel wire rope with Ø.037 nylon jacketed wire rope. Dimensions in brackets are millimeters ALTERNATE WIRE ROPE EXIT RANGES 100” (2.5 m) and GREATER 1, 2, 3...

SUPPLEMENTAL DATA DIMENSIONAL INFORMATION HX SERIES – RANGES TO 80” (2 m) HX SERIES – RANGES GREATER THAN 80” (2 m) 1. Transducer mounts with Ø.25 or M6 Socket head cap bolts. Dimensions in brackets are millimeters 1. ransducer mounts with Ø.50 or M12 socket head cap bolts. T 2. Dimension "C" is the cable offset that occurs as the cable is extended from the transducer. For "C" in inches, C = .0016 x E where E = extension in inches. For "C" in millimeters, C = .0016 x E where E = extension in mm. Dimensions in brackets are millimeters 4175 SW Research Way, Corvallis, Oregon 97333 U.S.A. |...