Plastic Modular Belt 23% Straight running belt Nominal pitch: 50.0 mm (1.97 in) Surface type: Flat Surface opening: 23% Backflex radius: 75.0 mm (3.00 in) Pin diameter: ø8 mm (1.97 in) Bottom view *uni-chains recommends this travel direction. However. travel in both directions is possible. Note: uni OPB 23% 4V are listed in the USDA “Accepted Meat and Poultry Equipment” publication as accepted food contact. Pin and lock material & color Non standard material and color: See uni Material and Color Overview. Alternative pin and lock materials: *Min. No. drive sprocket per shaft Permissible tensile force (Belt/pin material) Belt width Belt weight (Belt/pin material) Number of wear strips (Min. No.) **Return (pcs) Additional standard belt widths are available in steps of 151.0 mm (5.94 in.) Additional non-standard belt widths are available in steps of 33.6 mm (1.32 in.) Additional standard belt widths are available in steps of 151.0 mm (5.94 in.) Additional non-standard belt widths are available in steps of 33.6 mm (1.32 in.) General belt tolerance is +0/-0.4% at 23°C/73°F and 50% RH. For exact belt width contact Customer Service. Non standard belt width on request. Belt widths in PP-HW is 0.4 % wider than the belt widths in the table above *Max. Load per Drive Sprocket. Belt material: POM 2500 N (562 lbf), PP 1200 N (270 lbf), PE 500 N (270 lbf) **Max. Spacing between wear strips, Carry: 152 mm (6 in.) ; Return: 304 mm (12 in.) = Single Link STRAIGHT RUNNING Belt material & color

Accessories Flight Running direction Running direction Non Stick/Support Ribs Flight material & color Support Ribs Link size Non Standard material and color: See uni Material and Color Overview. Accessories Side Guard A Running direction Material & color * Min. indent Increment : 8.4 mm (0.33 in) Note: Backflex radius when side guards are used: 200.0 mm (7.90 in) Non Standard material and color: See uni Material and Color Overview.

Accessories Tab/NON STANDARD Running direction Belt material & color POM-D POM-LF Bottom Hold Down Non Standard material and color: See uni Material and Color Overview. Accessories Reinforcement Link The use of uni-chains belts with the SS reinforcement /pitch control links in blanchers. cookers and other high temperature applications will reduce belt elongation due to temperature by more than 90%. This will simplify the belt take-up system and reduce maintenance. uni-chains recommends one reinforcement link per K600 module. Material & color Steel Link Note: Reinforcement links require the use...

Molded sprocket Machined sprocket Other sprocket sizes are available upon request. Two-part sprocket are available upon request. Round bores are always delivered with keyway. Other bore sizes are available upon request. uni Retainer Rings: See uni Retainer Ring data sheet Max load per sprocket shown does not take bore size into account. Please also ensure that sufficient size shaft is chosen for corresponding load. For correct sprocket position: See uni Assembly Instructions for uni OPB. For more detailed sprocket information, contact Customer Service. Solid advice Ammeraal Beltech Modular A/S...

Datasheet: uni OPB 4V 23% Fine Meshed Plastic Modular Belt Type Straight running belt Nominal pitch: 50.0 mm (1.97 in) Surface type: Flat Surface opening: 23% Backflex radius: 75.0 mm (3.00 in) Pin diameter: ø8 mm (1.97 in) Bottom view *uni-chains recommends this travel direction. However. travel in both directions is possible. Pin and lock material & color Belt material & color Non standard material and color: See uni Material and Color Overview. Alternative pin and lock materials: Permissible tensile force (Belt/pin material) Belt width Belt weight (Belt/pin material) Number of wear *Min. No....

Datasheet: uni OPB 4V 23% Fine Meshed Accessories Flight Running direction Running direction Non Stick/Support Ribs Flight material & color Support Ribs Link size Non Standard material and color: See uni Material and Color Overview. Accessories Side Guard A Running direction Material & color * Min. indent Increment : 8.4 mm (0.33 in) Note: Backflex radius when side guards are used: 200.0 mm (7.90 in) Non Standard material and color: See uni Material and Color Overview.

Datasheet: uni OPB 4V 23% Fine Meshed Accessories Tab/NON STANDARD Running direction Belt material & color POM-D Bottom Hold Down Non Standard material and color: See uni Material and Color Overview. Accessories Reinforcement Link The use of uni-chains belts with the SS reinforcement /pitch control links in blanchers. cookers and other high temperature applications will reduce belt elongation due to temperature by more than 90%. This will simplify the belt take-up system and reduce maintenance. uni-chains recommends one reinforcement link per K600 module. Material & color Steel Link Note: Reinforcement...

Datasheet: uni OPB 4V 23% Fine Meshed Molded sprocket Machined sprocket Other sprocket sizes are available upon request. Two-part sprocket are available upon request. Round bores are always delivered with keyway.. Other bore sizes are available upon request uni Retainer Rings: See uni Retainer Ring data sheet Max load per sprocket shown does not take bore size into account. Please also ensure that sufficient size shaft is chosen for corresponding load. For correct sprocket position: See uni Assembly Instructions for uni OPB. For more detailed sprocket information, contact Customer Service. Solid...

Plastic Modular Belt uni OPB 4V Straight running belt Nominal pitch: 50.0 mm (1.97 in) Surface type: Rib Top Surface opening: 23% Backflex radius: 300.0 mm (11.80 in) Pin diameter: ø8 mm (1.97 in) Bottom view *uni-chains recommends this travel direction. However. travel in both directions is possible. Note: uni OPB 36% 4V are listed in the USDA “Accepted Meat and Poultry Equipment” publication as accepted food contact. Non standard material and color: See uni Material and Color Overview. Alternative pin and lock materials: *Min. No. drive sprocket per shaft Permissible tensile force (Belt/pin...