Exhibit with us
*mydirectindustry  
English
  1. Catalogs
  2. uni-chains
  3. 19.1 mm (0.75 in)

19.1 mm (0.75 in)

19.1 mm (0.75 in)
1 / 30 PagesView full catalog

19.1 mm (0.75 in)

Product catalog summary
Overview: This document is a technical datasheet for plastic modular belts and accessories by Ammeraal Beltech, detailing specifications, materials, colors, and accessories.
Specifications: The datasheet outlines specifications for the uni Light series belts, including a nominal pitch of 19.1 mm (0.75 in), surface types (Flat, Small rib), surface openings (10%, 18%, 22%), a backflex radius of 25.0 mm (1.0 in), and a pin diameter of ø5.0 mm (0.20 in).
Materials and Colors: Belts are available in materials such as POM-LF, PP, and PA6.6, with options for non-standard materials and colors as per the uni Material and Color Overview.
Accessories: Accessories include side guards, tabs, and hold-downs, with details on materials and dimensions. Non-standard accessories are available upon request.
Sprockets: Information on sprocket sizes, bore sizes, and dimensions is provided, with additional sizes and two-part sprockets available upon request.
Load and Tolerance: The datasheet specifies maximum load per drive sprocket, general belt tolerance at 23°C/73°F and 50% RH, permissible tensile force, and belt weight for various widths.
Recommendations: It is recommended to contact customer service for precise belt width and detailed sprocket information. Ensuring correct sprocket position and adequate shaft size for the load is advised.
Contact Information: Ammeraal Beltech Modular A/S contact details are provided for further inquiries.
Procedures: For correct sprocket positioning, refer to the uni assembly instructions specific to uni Light.
Additional Information: For more detailed sprocket information, contact Customer Service. For non-standard materials and colors, consult the uni Material and Color Overview.
See more

Catalog excerpts

19.1 mm (0.75 in)-1

Plastic Modular Belt C Straight running belt Nominal pitch: 19.1 mm (0.75 in) Surface type: Flat Surface opening: Closed Backflex radius: 25.0 mm (2.0 in) P in diameter: ø5.0 mm (0.20 in) Belt material & color Pin and lock material & color Non standard material and color: See uni Material and Color Overview. Alternative pin and lock materials: Permissible tensile force (Belt/pin material) Belt width Belt weight (Belt/pin material) Number of wear strips (Min. No.) *Min. No. drive sprocket per shaft Additional standard belt widths are available in steps of 76.4 mm (3.01 in.) Additional non-standard belt widths are available in steps of 19.1 mm (0.75 in.) Additional standard belt widths are available in steps of 76.4 mm (3.01 in.) Additional non-standard belt widths are available in steps of 19.1 mm (0.75 in.) General belt tolerance is +0/-0.4% at 23°C/73°F and 50% RH. For exact belt width contact Customer Service. Non standard belt width on request. The belt width in PA6 is 0.8 % wider than the belt width in the table *Max. Load per Drive Sprocket. Belt material: POM-LF 1250 N (281 lbf),PP 700 N (157 lbf), PA6 1250 N (281 lbf) **Max. Spacing between wear strips, Carry: 152 mm (6 in.) ; Return: 304 mm (12 in.) STRAIGHT RUNNING

 Open the catalog to page 1
19.1 mm (0.75 in)-2

Rough Belt Material & color Type Flat Rubber Material & color 03 Link size Other Non Standard Rubber profiles: See uni Rubber Profile Overview. Accessories Flight Running direction Flight Material & color PP-I Non Stick/Support Ribs Non Stick/Support Ribs Non Stick/Support Ribs Non Stick/Support Ribs Other Non Standard material and color: See uni Material and Color Overview.

 Open the catalog to page 2
19.1 mm (0.75 in)-3

Accessories Side Guard Side Guard Material & color PP-I Running direction Running direction Non Standard material and color: See uni Material and Color Overview. Running direction Type Bottom Hold Down Tab Material & color POM-D Non Standard material and color: See uni Material and Color Overview.

 Open the catalog to page 3
19.1 mm (0.75 in)-4

Pilot bore Bore size Overall diameter Molded sprocket Non standard material and color: See uni Material and Color Overview. Molded sprocket Other sprocket sizes are available upon request. Two-part sprocket are available upon request. Round bores are always delivered with keyway. Other bore sizes are available upon request. uni Retainer Rings: See uni Retainer Ring data sheet. Width of tooth = 4.8 mm (0.19 in) Width of sprocket = 25.0 mm (0.98 in) Max load per sprocket shown does not take bore size into account. Please also ensure that sufficient size shaft is chosen for corresponding load. Fabriation...

 Open the catalog to page 4
19.1 mm (0.75 in)-5

Plastic Modular Belt CR Straight running belt Nominal pitch: 19.1 mm (0.75 in) Surface type: Rough Top Surface opening: Closed Backflex radius: 25.0 mm (1.0 in) Pin diameter: ø5.0 mm (0.20 in) Recommended Belt material & color Recommended Pin material & color Non standard material and color: See uni Material and Color Overview. Alternative pin and lock materials: Permissible tensile force (Belt/pin material) Belt width Belt weight (Belt/pin material) *Min. No. drive PA6/PBT-GR sprocket per shaft kg/m lb/ft Number of wear strips (Min. No.) **Carry (pcs) Additional standard belt widths are available...

 Open the catalog to page 5
19.1 mm (0.75 in)-6

Rough Belt Material & color Type Flat Rubber Material & color 03 Link size Other Non Standard Rubber profiles: See uni Rubber Profile Overview. Accessories Flight Running direction Flight Material & color PP-I Non Stick/Support Ribs Non Stick/Support Ribs Non Stick/Support Ribs Non Stick/Support Ribs Other Non Standard material and color: See uni Material and Color Overview.

 Open the catalog to page 6
19.1 mm (0.75 in)-7

Accessories Side Guard Side Guard Material & color PP-I Running direction Running direction Non Standard material and color: See uni Material and Color Overview. Running direction Type Bottom Hold Down Tab Material & color POM-D Non Standard material and color: See uni Material and Color Overview.

 Open the catalog to page 7
19.1 mm (0.75 in)-8

Pilot bore Bore size Overall diameter Molded sprocket Non standard material and color: See uni Material and Color Overview. Molded sprocket Other sprocket sizes are available upon request Two-part sprocket are available upon request Other bore sizes are available upon request uni Retainer Rings: See uni Retainer Ring data sheet Width of tooth = 4.8 mm (0.19 in) Width of sprocket = 25.0 mm (0.98 in) Max load per sprocket shown does not take bore size into account. Please also ensure that sufficient size shaft is chosen for corresponding load. Fabriation & service For correct sprocket position:...

 Open the catalog to page 8
19.1 mm (0.75 in)-9

Plastic Modular Belt 10% Straight running belt Nominal pitch: 19.1 mm (0.75 in) Surface type: Flat Surface opening: 10% Backflex radius: 25.0 mm (2.0 in) P in diameter: ø5.0 mm (0.20 in) Belt material & color Non standard material and color: See uni Material and Color Overview. Pin: PE W Alternative pin and lock materials: Permissible tensile force (Belt/pin material) Belt weight (Belt/pin material) Belt width *Min. No. drive sprocket per shaft Number of wear strips (Min. No.) **Carry (pcs) Additional standard belt widths are available in steps of 76.4 mm (3.01 in.) Additional non-standard belt...

 Open the catalog to page 9
19.1 mm (0.75 in)-10

Rough Belt Material & color Type Flat Rubber Material & color 03 Link size Other Non Standard Rubber profiles: See uni Rubber Profile Overview. Accessories Flight Running direction Flight Material & color PP-I Non Stick/Support Ribs Non Stick/Support Ribs Non Stick/Support Ribs Non Stick/Support Ribs Other Non Standard material and color: See uni Material and Color Overview.

 Open the catalog to page 10
19.1 mm (0.75 in)-11

Accessories Side Guard Side Guard Material & color PP-I Running direction Running direction Non Standard material and color: See uni Material and Color Overview. Running direction Type Bottom Hold Down Tab Material & color POM-D Non Standard material and color: See uni Material and Color Overview.

 Open the catalog to page 11
19.1 mm (0.75 in)-12

Pilot bore Bore size Overall diameter Molded sprocket Non standard material and color: See uni Material and Color Overview. Molded sprocket Other sprocket sizes are available upon request. Two-part sprocket are available upon request. Round bores are always delivered with keyway. Other bore sizes are available upon request. uni Retainer Rings: See uni Retainer Ring data sheet. Width of tooth = 4.8 mm (0.19 in) Width of sprocket = 25.0 mm (0.98 in) Max load per sprocket shown does not take bore size into account. Please also ensure that sufficient size shaft is chosen for corresponding load. Fabriation...

 Open the catalog to page 12

All Uni-chains catalogs and technical brochures

  1. uni-ACB-C
    uni-ACB-C

    4  Pages

  2. uni UltraClean
    uni UltraClean

    4  Pages

  3. uni Retainer Rings
    uni Retainer Rings

    2  Pages

  4. Idler
    Idler

    2  Pages

  5. uni JCB Y
    uni JCB Y

    2  Pages

  6. uni SNB M2 50%
    uni SNB M2 50%

    4  Pages

  7. uni S-MPB CS 22%
    uni S-MPB CS 22%

    4  Pages

  8. uni S-MPB C
    uni S-MPB C

    4  Pages

  9. Series uni 2700 Type LH
    Series uni 2700 Type LH

    2  Pages

  10. Special Plastic Chain
    Special Plastic Chain

    35  Pages

  11. Series uni 1873 Type Grip D
    Series uni 1873 Type Grip D

    2  Pages

  12. Series uni Flex OSB Type 60% Open Radius 2.2
    Series uni Flex OSB Type 60% Open Radius 2.2

    2  Pages

  13. Serie uni NTB Type C
    Serie uni NTB Type C

    2  Pages

  14. UniChains Catalog
    UniChains Catalog

    683  Pages

  15. Installation and maintenance
    Installation and maintenance

    26  Pages

  16. Automotive Brochure
    Automotive Brochure

    6  Pages

  17. Uni CSB
    Uni CSB

    4  Pages

  18. Uni JCB
    Uni JCB

    4  Pages

  19. 63.5 mm (2.50 in)
    63.5 mm (2.50 in)

    18  Pages

  20. 50.8 mm (2.0 in)
    50.8 mm (2.0 in)

    86  Pages

  21. 50.0 mm (1.97 in)
    50.0 mm (1.97 in)

    68  Pages

  22. 38.1 mm (1.50 in)
    38.1 mm (1.50 in)

    60  Pages

  23. 27.9 mm (1.10 in)
    27.9 mm (1.10 in)

    2  Pages

  24. 25.4 mm (1.0 in)
    25.4 mm (1.0 in)

    46  Pages

  25. 12.7 mm (0.50 in)
    12.7 mm (0.50 in)

    22  Pages

  26. Chains
    Chains

    172  Pages

  27. Belt catalog
    Belt catalog

    180  Pages

Archived catalogs

  1. CHAIN CATALOG
    CHAIN CATALOG

    125  Pages

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.