User manual and Spare parts Edition Reviced Language Original user manual

Warranty This Underhaug product is guaranteed against manufacturing and material defects for one year. Components not produced by Underhaug, such as electrical and hydraulic equipment, power take-off shafts, and tires, are covered according to the original manufacturer's warranty terms. The following components have limited warranty terms due to their function: tires, skirts, blade tips, breaker pins, fuses, hydraulic seals in pumps, motors, valves, cylinders, etc., as found on new machines. Deterioration due to wear and tear during use is considered normal for these parts. Therefore, the warranty...

Safety Before operating the machine Before operating, adjusting, or repairing the machine, the user, repairer, and owner must familiarize themselves with the safety instructions provided in this manual (Fig 1). Be attentive and cautious when working with agricultural machinery. Read and take note of the safety instructions in this manual. Safety at work is your responsibility General safety instructions Exercise caution when other people or animals are nearby Never start the machine when people or animals are close to the machine and tractor. Never stand between the tractor wheels and the machine...

The tractor engine should be stopped and the ignition key removed before performing any repair work, lubrication, or other maintenance on the machine. (Fig. 6). Ensure that all covers are in good condition and properly mounted. Do not attempt to start the machine until this has been done. Damaged covers should be repaired or replaced immediately. (Fig. 7). Pay special attention to all protective covers related to the power take-off shafts. Replace damaged covers. Safety chains must always be attached to the machine and/or tractor to prevent the protective sleeves from rotating. Be cautious when...

When disconnecting the machine and leaving the tractor/machine Set all hydraulic functions to the neutral position when disconnecting the machine. Lower the movable working components to the ground or set them in the transport position and secure them. If the machine is equipped with parking blocks, these should be used. Do not allow children to play or remain near agricultural machines. (Fig. 9). Drive Safely Remember, you are responsible – carelessness and negligence can cause serious injury or even death. (Fig. 10). Check the wheel bolts and the connection between the machine and tractor before...

Supplementary safety instructions for UM 6150 Potato Harvester This equipment is marked with this warning label be replaced. . If the label is damaged, it must Warning label 2935064 (fig. 1). Be cautious. Read and understand the instruction manual before using the equipment, and before adjusting and performing maintenance. Warning label 220525B (fig. 2). Due to the high risk of pinching, it is important to keep people at a safe distance from the equipment while in use. Hands and legs can be pinched under/in the machine. Maintain distance during use, but also during transport and adjustments....

Before the machine is used, adjusted, or overhauled, it is crucial that this instruction manual is read thoroughly. This will ensure the highest level of safety and help the machine operate satisfactorily. All references to left and right directions refer to the positions of components when standing behind the machine and facing the direction of travel. The dealer should be contacted if operational problems arise. The staff there are familiar with the machine and can offer advice. Follow the safety instructions. After the first hours of operation, and periodically thereafter, check and tighten...

Technical Data Working components: Capacity: Belt width: Effective belt length: Weight: Depth wheels: Transport dimensions: 1-row three-point mounted storage harvester Cutter, belt, belt drive, shaker wheels 1-4 da per hour 70 cm 49.5 cm Technical Information The machine is connected to the tractor’s three-point linkage, category 1 or 2. How the machine is used and adjusted has a significant impact on the final result, i.e., the quality of the potatoes, cleaning, etc. Drive into the field. Adjust the drag connections so that the drill enters the middle of the blade. If the machine is not aligned...

• Short top link = Heavy sifting • Long top link = Light sifting (increased wear on the belt) Adjusted using the hydraulic position control and depth wheels. • Normal setting = as shallow as possible • Exception: On light sandy soil, set deeper to get more soil on the belt. The forward driving speed should also be considered based on the amount of material being fed into the machine. On very light soil, it might be beneficial to replace the front and rear shaker wheels with belt wheels. Tighten screws and nuts regularly. Pay special attention to the nuts on the shaker wheel axles and screws that...

9. Spare parts Efforts have been made to replicate the original parts as closely as possible. However, Underhaug AS reserves the right that some new parts may not fit older models (UM-2000, 550) of Underhaug Potato Harvesters, as production of these models was discontinued in 2002.

SPARE PARTS UM 6150 - Fig. 1: Frame Art. No. Qty Item Description Side plate left Side plate right Front frame Diagonal stay Parking foot Safety pin Fastener Bearing clamp Top link bolt Lower link bolt Link bolt pin Stone rejector left Stone rejecter right Guide plate left Guide plate right Cutting edge left Cutting edge right Stone cather left Stone cather right Tow hitch left Tow hitch right Clevis for drawbar Plug 50 x 50 Plug 80 x 80 Hex. scr 931-1-M12x120 Hex. scr 933-M12x30 Hex.scr 933-M12x35 Hex.scr 933-M12x50 Locking scr 603-M8x20 Loking scr 603-M10x30 Special plow bolt M12x38 Loking...

Item Description Belt cpl. UM6150 Belt rod Locking rod Belt roller Bearing 6304 Sealing ring Ring Spring washer 127-A16 Nut M16 spec. Belt wheel cpl. Agtitiation wheel cpl. Belt wheel Capsule plate Washer 125-A17 Hex. scr 933 M16x110 Nut 934-M16 Locking nut 985-M16 Agitiation wheel welded Return rollers cpl. Axle for belt wheel Belt wheel Pin ISO 1234-5x35 Capsule plate Washer 125-A13 Locking nut 985-M10 Bearing housing 072 Locking ring 471-A30x1,5 Support ring 30x42x2,5 Ball bearing 6306-RS1 Washer 125-A10,5 Hex.scr 931-1-M10x75 Keyed washer 3912 8x16 Cross shaft Sprocket Ball bearing 6207-2RS1...