User manual and spare parts Edition Reviced Language Original user manual

Warranty This Underhaug product is guaranteed against manufacturing and material defects for one year. Components not produced by Underhaug, such as electrical and hydraulic equipment, power take-off shafts, and tires, are covered according to the original manufacturer's warranty terms. The following components have limited warranty terms due to their function: tires, skirts, blade tips, breaker pins, fuses, hydraulic seals in pumps, motors, valves, cylinders, etc., as found on new machines. Deterioration due to wear and tear during use is considered normal for these parts. Therefore, the warranty...

Safety Before operating the machine Before operating, adjusting, or repairing the machine, the user, repairer, and owner must familiarize themselves with the safety instructions provided in this manual (Fig 1). Be attentive and cautious when working with agricultural machinery. Read and take note of the safety instructions in this manual. Safety at work is your responsibility General safety instructions Exercise caution when other people or animals are nearby Never start the machine when people or animals are close to the machine and tractor. Never stand between the tractor wheels and the machine...

The tractor engine should be stopped and the ignition key removed before performing any repair work, lubrication, or other maintenance on the machine. (Fig. 6). Ensure that all covers are in good condition and properly mounted. Do not attempt to start the machine until this has been done. Damaged covers should be repaired or replaced immediately. (Fig. 7). Pay special attention to all protective covers related to the power take-off shafts. Replace damaged covers. Safety chains must always be attached to the machine and/or tractor to prevent the protective sleeves from rotating. Be cautious when...

When disconnecting the machine and leaving the tractor/machine Set all hydraulic functions to the neutral position when disconnecting the machine. Lower the movable working components to the ground or set them in the transport position and secure them. If the machine is equipped with parking blocks, these should be used. Do not allow children to play or remain near agricultural machines. (Fig. 9). Drive Safely Remember, you are responsible – carelessness and negligence can cause serious injury or even death. (Fig. 10). Check the wheel bolts and the connection between the machine and tractor before...

Supplementary safety instructions for UM 5150 Potato planter This equipment is marked with this warning label be replaced. . If the label is damaged, it must Warning label 2935064 (fig. 1). Be cautious. Read and understand the instruction manual before using the equipment, and before making adjustments or performing maintenance. Warning label 220525B (fig. 2). Due to the significant risk of pinching, it is important to keep people at a safe distance from the equipment while in use. Special pinching hazard around the rotors during potato planting. Potatoes must be dropped into the rotor. Ensure...

Underhaug's UM-5150 semi-automatic potato planter is two machines in one. The planter can be converted into a ridger in just a few minutes. The machine is primarily designed for those who grow potatoes on a smaller scale and cannot justify the purchase of a fully automatic potato planter. It is also well-suited for those who specialize in early production and exclusively use presprouted seed potatoes. Self-sufficiency, farm shops, and locally produced goods are also popular points today. • Row spacing can be adjusted from approximately 65 cm to approximately 85 cm. • The width of the ridging...

Technical data Weight: Depth: Width: Height: Connection to Tractor The machine is connected to the tractor's three-point hitch. The included top link and drawbar bolts can be adjusted to category 1 or category 2 as needed. Maintenance Lubricate all grease points daily. The machine should be stored indoors when not in use. Protect shiny parts from rust.

Item Description Frame Rotor frame Hitch connector Board support L Board support R Angle support Wood board Seat Top link bolt Lower link bolt Link bolt pin Sleeve Hex. Screw DIN 933 - M12 x 40 Hex. Screw DIN 933 - M12 x 45 Hex. Screw DIN 933 - M16 x 30 Hex. Screw DIN 933 - M16 x 45 Hex. Screw DIN 933 - M16 x 90 Locking screw DIN 603 - M12 x 50 Locking screw DIN 603 - M16 x 40 Washer DIN 125 - A 13 Washer DIN 125 - A 17 Nylock nut DIN 985 - M 12 Nylock nut DIN 985 - M16

SPARE PARTS UM 5150 – OPERATION FIG. 2 Ref. Item Description Rotor frame Rotor Rotor mount L Rotor mount R Chain wheel cover Bracket for cover Axle Gear Pinion Insert sleeve Spoke Arm for spoke wheel Pressure plate for spokes Chain w/chain wheel cpl. Chain cpl. Grease nipple M6 ISO 4026 M10x16 Front chain wheel Rear chain wheel cpl. Rear spoke wheel Anker plate w/threads Anker plate Umbraco lowering, flat DIN 7991 – M8 x 25 Hex. Screw DIN 933 – M8 x 25 Hex. Screw DIN 933 – M10 x 35 Hex. Screw DIN 933 – M10 x 45 Hex. Screw DIN 933 – M12 x 45 Hex. Screw DIN 933 – M12 x 70 Washer DIN 125 – A 8,4...

SPARE PARTS UM 5150 - DEPT WHEEL FIG. 3Art. No. Qty 289095 1 Item Description Outer pipe Inner pipe Wheel 4.00 x 4 cpl. Mounting bolt Washer DIN 9021 - 22 Nylock nut DIN 985 - M20 Locking spring

Item Description Ridging showel 450mm Point w/bolt Support plate Left wing Right wing Elastic hook Spring bolt Spring brace Spring Washer DIN 9021 A13 Nylock nut DIN 985 M12 Mounting bracket Hex. screw DIN 933 M16 x 35

Item Description Furrow opener R, assy Furrow opener L, assy Furrow opener

Responsible person Name Position Company Address Phone Atle Årsland General Manager Underhaug AS Torlandsvegen 3 4365 Nærbø, NORWAY +47 51 43 49 78 Declares that the following machine: Manufacturer: Type: Serial Number: Production Year: Underhaug AS UM 5150 Potato Planter complies with the following directive: Maximum regulation 554 (for 2009-05-20-554) and meets essential health and safety requirements. Basic standard ISO 12100 _______________________________________ Atle Årsland ______________________ Nærbø, date