UM 7705 Round Bale Handler Instruction and spare parts Edition Revised Language Original user manual 1

Warranty This Underhaug product is warranted against manufacturing and material defects for a period of one year. Components not manufactured by Underhaug, such as electrical and hydraulic equipment, power take-off (PTO) shafts, and tires, are covered according to the original manufacturer’s warranty terms. Limited warranty for specific components Due to their functional nature, the following components have limited warranty coverage: Tires, blades, blade tips, shear bolts, fuses, and hydraulic seals in pumps, motors, valves, and cylinders, etc. Wear and tear resulting from normal use is considered...

Safety Before operating the machine Before operating, adjusting, or repairing the machine, the user, repairer, and owner must familiarize themselves with the safety instructions provided in this manual (Fig 1). Be attentive and cautious when working with agricultural machinery. Read and take note of the safety instructions in this manual. Safety at work is your responsibility General safety instructions Exercise caution when other people or animals are nearby Never start the machine when people or animals are close to the machine and tractor. Never stand between the tractor wheels and the machine...

The tractor engine should be stopped and the ignition key removed before performing any repair work, lubrication, or other maintenance on the machine. (Fig. 6). Ensure that all covers are in good condition and properly mounted. Do not attempt to start the machine until this has been done. Damaged covers should be repaired or replaced immediately. (Fig. 7). Pay special attention to all protective covers related to the power take-off shafts. Replace damaged covers. Safety chains must always be attached to the machine and/or tractor to prevent the protective sleeves from rotating. Be cautious when...

When disconnecting the machine and leaving the tractor/machine Set all hydraulic functions to the neutral position when disconnecting the machine. Lower the movable working components to the ground or set them in the transport position and secure them. If the machine is equipped with parking blocks, these should be used. Do not allow children to play or remain near agricultural machines. (Fig. 9). Drive Safely Remember, you are responsible – carelessness and negligence can cause serious injury or even death. (Fig. 10). Check the wheel bolts and the connection between the machine and tractor before...

Instructions for UM 7705 Round bale handler This equipment is marked with this warning sign. If the sign is damaged, it must be replaced. Warning sign 220532 (fig. 1). Remember! Read and understand the instruction manual before using the equipment and before adjusting and performing maintenance. Warning Sign 220532 (Fig. 1). Caution. Read and understand the instruction manual before using the equipment, and before adjusting or performing maintenance. Warning Sign 220538 (Fig. 2). Due to the high risk of crushing, it is essential to keep people at a safe distance when the equipment is in use....

Technical Data Weight: Maximum width: 1900 mm (grabbing arms in outer position) Lifting capacity: Optional Equipment 7708 Mounting plates (for welding coupling hooks) 7709 Mounting plate extension (increases total coupling width from 1150 to 1250 mm) (Coupling hooks can be welded directly to the frame when the distance between the coupling hooks (c/c) is 700-830 mm) 7710 Overhead arm 7712 Round bale spikes (2 pieces) 7714 3-point hitch category 2 Requires a double-acting hydraulic outlet. Preparation of new equipment Mount the grabbing arms. Tighten the nuts to 65-70 Nm torque. Note! The nut...

Connection to tractor The round bale grab is connected to the front loader or 3-point hitch (remember correct attachment equipment). It is operated by the double-acting valve. The front loader should have a hydraulically adjustable attachment. Use of the round bale grab Align the grabbing arms parallel to the ground. Move the grabbing arms to the outer position before driving the grab into the bale. If the round bale grab has an overhead arm (7710), lay it down on the bale. Press the arms underneath the bale so that it is securely held. When stacking bales, ensure that the grabbing arms do not...

ROUND BALE GRAB UM 7705 Nylock nut M16 GALV. Parts marked with * have been modified since 2000.04.01 Item Description COMPLETE FRAME Frame, welded Arm, welded L and R Grease nipple M6-45 GR. Axle 035x220-016.5/16 Hex screw M16x100-8.8 GALV. Nylock nut M16 GALV. Cylinder DV 063/032x900+250 Cylinder sealing kit 063/032 Grease nipple M6 Straight Hydraulic hose 3/8’’2265 Quick coupling ‘’male Fitting 3/8’’--‘’_’’BSP UU O-ring ‘’Bond Seal Dust protector Blue Dust protector Yellow Bolt Washer 031-056x4 Locking angle Clamping sleeve 12x50 ELZN ROLLER SPINDLE COMPLETE Axle Ball bearing 6210-2RS Support...

ROUND BALE GRAB UM 7005 Ref. Part No. Qty FIG. 2Item Description ROUND BALE SPIKES COMPL. OVERARM Overarm mounting Hex screw M12x30-8.8 GALV Nylock nut M12 GALV Washer 013-024x2.5 Welded overarm Hex screw M16x110-8.8 GALV Nylock nut M16 GALV Washer 017-030x3 Support plate TOP LINK MOUNTING FOR OVERARM Top link mounting welded Left pull bar mounting welded Right pull bar mounting welded

Item Description THREE-POINT LINKAGE KIT Top link mounting welded Hex screw M12x30-8.8 GALV Nylock nut M12 GALV Washer 013-024x2.5 End plug 80x80 Right pull bar mounting welded Left pull bar mounting welded Clamp 4KT. 101.5-M16 Nylock nut M16 GALV Support plate Left mounting plate Right mounting plate Clamp 4KT. 101.5-M16 Hex screw M20x50-8.8 GALV Nylock nut M20 GALV Nylock nut M16 GALV MOUNTING PLATE EXTENSION Mounting plate extension

Responsible person Name Position Company Address Phone Atle Årsland General Manager Underhaug AS Torlandsvegen 3 4365 Nærbø, NORWAY +47 51 43 49 78 Declares that the following machine: Manufacturer: Type: Serial Number: Production Year: Underhaug AS UM 7005 Round bale handler complies with the following directive: Maximum regulation 554 (for 2009-05-20-554) and meets essential health and safety requirements. Basic standard ISO 12100 _______________________________________ Atle Årsland ______________________ Nærbø, date