Panel I/O – Processor and Multifunction I/O Board with 16 A/D, 2 D/A, 20 DIO, One I2C and One RS-232/422/485 Port
4Pages

• Compact board level size (4.5" x 8.5" x 0.75") • Small enough to be mounted behind an instrument panel • Standard Ethernet Interface • IEEE-1588/PTP and 1PPS synchronization • Rugged (5g Vibe, 100g Shock, -40°C - +85 °C) • MTBF > 140,000 hours (>15 years) • Complete Windows, Linux and RTOS software support • Fully compatible with UEI DNA/DNR software (same API) • PC-based or standalone/embedded controller operation • Hex switches allow selection of IP address without a PC Multifunction Panel I/O Interface • 16 SE / 8 Differential 18-bit analog input channels • ±80 to ± 0.156 V analog input ranges • Dual 16-bit ±10 V or 0-20 mA analog output channels • Sixteen 0-55 VDC digital I/O bits, four TTL DIO bits • 500 mA DOuts with 16-bit PWM resolution • Dual 32-bit counters and 4 logic level DIO • Up to 2 kHz update rates • Trigger input and output • RS-232/422/485 and I2C ports • 350 Vrms Isolation General Description: The UEI-PIO-1010 is a fully integrated I/O system. At 4.5" x 8.5" x .75" it is small enough to easily fit between an instrument panel and the bulkhead of a simulator/trainer, or in a huge variety of other tight spaces. With over 40 I/O channels, the combination of small size and large I/O count makes it an ideal solution for a wide variety of applications. The 15+ year MTBF combined with the unit’s rugged construction means it’s ideally suited for installation in locations without easy access. It is not going to need either routine service or repairs. I/O Description: The multifunction I/O ensures you have the type of I/O you need, and the high channel density ensures you have all the I/O channels required in the panel space available. The UEI-PIO-1010 offers a powerful combination of I/O, including 16 single-ended/8 differential analog inputs, 2 analog outputs, 20 bits of digital I/O, an I2C port and an RS-232/422/485 port. The UEI-PIO-1010 offers 8 software selectable A/D ranges from ±80 V to ±0.156 V with 18-bit resolution. The ±80 Volt range makes the PIO-1010 an ideal measurement solution in a host of simulation, aerospace, automotive and power generation applications, where many DAQ products’ Deployment Options: Based on the same SoloX/ARM-based processor used in our popular Cube 10 volts maximum input range cannot be used without external signal conditioning. The “high voltage” and “low and RACKtangle series, the UEI-PIO-1010 may voltage” configurations are programmable be configured in PowerDNA mode, where the SLOTS FOR on a per-channel basis. Programmable chassis operates as a slave to a host PC, or in 2 ADDITIONAL gains combined with the board’s UEIPAC mode, where it operates in a fully I/O BOARDS 18-bit A/D converter provides resolution as stand-alone/embedded or SCADA modes. low as 1.19 microvolts. The PIO-1010 provides PowerDNA mode: In PowerDNA mode, sample rates as high as 1000 samples per the chassis operates as a slave I/O device, second on each channel (16 k/s aggregate). running under the control of a host PC. All Two D/A channels offer either ±10 Volt or application code in this mode is created and 4-20 mA outputs with 16-bit resolution and run on the host. The host PC controls the provide 20% overrange capability. device using standard PowerDNA libraries and The unit offers 20 bits of digital input/output standard tools. PowerDNA mode offers almost broken into 16 bits of industrial voltage I/O unprecedented software support, including: and 4 bits of logic-level I/O (settable in banks of 2). Each bit of DIO may be • ll popular operating systems, including Windows, Linux, VxWorks, QNX, A independently set as input or output. Industrial inputs and outputs have RTX and InTime. a wide operating range from 3.3 V to 55 VDC. The industrial range (not • ll popular programming languages, including C, C#, C++, Python, JAVA, logic-level) inputs have programmable pull up/down resistors that can be A independently enabled and allow inputs to monitor contacts connected to VB and VB.NET. a supply voltage or ground. Inputs are sensed with an A/D that can sample • ll popular application packages, including MATLAB, Simulink, LabVIEW, A up to 200 kHz, so high and low voltage thresholds are programmable and and more. allowing change of state detection with 5 µs resolution. The industrial (not UEIPAC Embedded/Standalone/SCADA mode: In UEIPAC mode, the logic-level) outputs can be set as current sourcing (switch between Vcc and standard firmware running on a traditional PowerDNA chassis is replaced the output), current sinking (switch between Gnd and the output), pushby a standard Linux operating system. The user then writes the Linux pull (connect to Vcc or Gnd, not at the same time) or can act as a simple application that runs on the UEI-PIO-1010 hardware. For more information switch to Vcc or Gnd. These are divided into banks of 4, and each bank can on the UEIPAC deployment, please see the specifications shown on the be connected to a different Vcc if required. Industrial digital outputs can be configured as flexible high resolution lighting controllers with PWM or following page or visit the UEIPAC on our website. softstart outputs with 16-bit pulse width resolution. The PWM/softstart The UEI-PIO-1010 uses an ARM Cortex-A9 processor running at 1 GHz. With parameters are selectable on a per-channel basis. Outputs are protected with 1 GByte of RAM and 8 GByte of eMMC FLASH, the unit has plenty of CPU 1.25 Amp fast-blow fuses. capability to handle even the most challenging I/O application. The unit Analog input, industrial digital input (including digital in, analog values and also provides a eUSB slot for SSD storage. change of state), serial and I2C data may be streamed to their own FIFOs or a The UEI-PIO-1010 is also available in different deployment options, single combined FIFO with timestamps. AIn/Din time stamps are generated including UEISIM, UEI iDDS, UEIMODBUS and UEIOPC. More information on at the start of the scan, while each byte of serial data received is time stamped these deployment options can be found below, or see our website.* upon receipt. UEISIM series: Simulink users will appreciate the ability to use Simulink Two 32-bit counters are provided which can be connected to any digital input Coder to compile and deploy their models on the UEISIM hardware. pin, while the counter outputs can be used to drive two dedicated industrial UEIPAC iDDS series: This deployment can be configured to run the rapidly outputs. TTL level trigger in/out out are also provided. growing family of iDDS products with Historian functionality. System The UEI-PIO-1010 also includes two communications ports. The first is configuration is made easy by an intuitive, easy to use web/HTML interface. * For access to a serial terminal, you will need the CBL-PIO-DBG cable. United Electronic Industries, Inc. Tel: (508) 92