
Intelligent 9 SD/microSD Duplicator & Sanitizer User Manual
Open the catalog to page 1Product Disclaimer U-Reach is not accountable for any incidental or consequential damages, including, but not limited to property harm, loss of time or data from use of any U-Reach product, or any other damages attributable to product malfunction or failure of including without limitation, those attributed to reliance of the materials provided, costs of product replacement, loss of use, data or profits, delays or business interruptions, any principle of legal responsibility arising from or in reference to the use, overall performance, delays in servicing, or lack of ability to render service...
Open the catalog to page 3• Carefully read the entire manual before operating. • Never turn off the power while the firmware is updating. • Devices will operate at high temperature during high-speed tasks. Please wear protective gloves to prevent burns when handling devices. • Devices working in high temperature may cause it to slow down or even shut down. Please make sure the devices are not overheated. • Ensure machine and operator are properly grounded to prevent ESD. • Make sure the source device is correct and functioning. • Equal capacity of source and target is recommended for guaranteed data consistency. • Using...
Open the catalog to page 4Special items, procedures, or notes to be observed prior to use.
Open the catalog to page 5Product Introduction Front View LCD Display Control Buttons ▲: Forward ▼: Backward OK: Confirm ESC: Escape LED Indicator Green: Pass/Working Red: Fail Back View Power Switch Power Supply USB Port for PC-Monitoring
Open the catalog to page 6PC-Link Software Disc x 1 Power Adapter Each model may require a different power adapter per its need. The following reference table illustrate adapter requirements for each series. Reference table (ComboSD/ MicroSD)
Open the catalog to page 7*Below functions and features subject to change without notice.
Open the catalog to page 8Step 1: Prepare source and target devices.
Open the catalog to page 14failed. Removing the flash card during copy is strongly discouraged as it will damage the flash card. Backup the data on target flash cards before starting the copying process as any pre-existing data will be lost once copy is complete. 2. Compare The compare function checks the accuracy of copy result. Scroll to select "2. Compare", then press "OK" to start the verification process. 3. Copy+Compare Sequentially automates from Function 1, Copy to Function 2, then Compare. Scroll to select "3. Copy+Compare", then press "OK" to start the automated duplication and verification process. Functions...
Open the catalog to page 15Test Capacity Pass Quantity Reading Speed Fail Quantity This function will not alter the content or format. You can set the checking range in [4. Media Check >> Setup Range]. 4.2 H5 Test This function performs a read and write test to determine the flash’s quality. The flash’s original data will be erased during this test. Use the ▲▼buttons to view the status of each port. Bad Sector Pass Quantity Test Capacity Fail Quantity The flash device will be formatted at FAT 16/32 once testing is complete. 4.3 H6 Test This function performs a read and write test on the empty space to determine the flash’s...
Open the catalog to page 164.4 Setup Range % This function sets the quality check capacity range. Use the▲▼buttons to set the range from 1 to 100%. The higher the percentage, the longer it takes. [Setup Range] 100% 4.5 Setup Range MB This function sets the quality check capacity range in MB. Use the▲▼buttons to set the range from 1MB to 9000MB. [Setup Range MB] 2000MB The duplicator will abide by whichever was set last if both Range% and Range MB are set. 4.6 Setup Error Limit This function sets the error tolerance range while checking the flash. Use the ▲▼ buttons to set the error limit value. Select units to use (KB...
Open the catalog to page 174.8 Minimum Write Speed This function can be used to select the flash media whose writing speed is too slow. Users can set an expected minimum writing speed for media check, so the flash media that doesn’t reach the minimum speed value will be identified. [Minimum Write Speed] 10.0MB/Second When the red-light illuminates to indicate that an error has occurred, use the▲▼buttons to view the error information. 4.9 Low Speed Tolerance Time Sets the tolerance time when flash does not reach the minimum speed from 10~99 seconds. The default value is 20 seconds. 4.10 Set Capacity Limit This function...
Open the catalog to page 18This setting displays the flash media's basic information such as file format, content size, and total capacity. Use the ▲▼ buttons to view the information of each flash media, source included. Total Capacity of the Device Data Size Using this function will not delete the flash media content or format. This function displays system information such as model number and software version. Press ▼ for further information This function formats flash into FAT. Plug in the flash media and press "OK". The system will automatically detect its capacity, then format the media per its capacity. • If the...
Open the catalog to page 19The system will format per flash's capacity. If capacity is above 2GB, the system will format the flash to FAT32 and below 2GB, the system will format the flash to FAT16. Sets the exFAT format. Sets the FAT16 cluster size. Sets the FAT32 cluster size. The source port will not perform any formatting because this function will delete the flash media s data. This function measures the "read" and "write" flash media speed. O Plug flash media into the slot, select function [3. Measure Speed], then press "OK" to start this function. SD Duplicator 2. Measure Speed 0 Use the ▲▼keys to view the exact...
Open the catalog to page 20To protect source data, the system will not execute “Measure Speed” on the master device. The function may alter the format and data content of flash. 6.3 Capacity Check This function can quickly check the real capacity if it’s claimed. ➊ Plug in flash media, select function [6.3 Capacity Check], then press "OK". It will take about 3 seconds to determine the exact capacity. ➋ System will show the checking result by use of Green/Red LED light. ➌ Use the ▲▼buttons to check the status of each slot. Green Light: Capacity OK This function supports asynchronous operation; you can continually plug and...
Open the catalog to page 2121 Pages
19 Pages
18 Pages
31 Pages
31 Pages
23 Pages
23 Pages
37 Pages
21 Pages
24 Pages
4 Pages
41 Pages
2 Pages
41 Pages