
SATA III Ultra-High Speed Sanitizer and Duplicator User Guide v A.03
Open the catalog to page 1Product Disclaimer The manufacturer is not accountable for any incidental or consequential damages, which includes, but is not constrained to property harm, loss of time or data from use of our product, or any other damages attributable to product malfunction or failure (including without limitation, those attributable to: (1) reliance of the materials provided, (2) costs of product replacement, (3) loss of use, data or profits, (4) delays or business interruptions, (5) and any principle of legal responsibility, arising out of or in reference to the use or overall performance or from delays in...
Open the catalog to page 3Important Notice • Carefully read the entire manual before operating. • Make sure the source device is correct and functioning. • Equal capacity of source and target is recommended for guaranteed data consistency. • Using the Copy+Compare function provides the most flawless duplication. • Damage incurred due to non-compliance with our operating instructions will void the warranty. • Store the equipment safely when not in use and keep out of the reach of children. • Please turn off duplicator before replacing sockets. • Never turn off the power while the firmware updates. • Use only approved,...
Open the catalog to page 4Product Overview Hardware overview Red: Fail Flashing Green: Operating Remain Green: Pass Yellow: Powered UP: Backward OK: Confirm/OK DOWN: Forward ESC: Cancel/Back LCD configuration Total Size Target HDD Function Time Copy Progress % Copied Processed Size (Target
Open the catalog to page 5This function will show information of the duplicator system, including controller model, number and software version.
Open the catalog to page 7Step 1: Prepare source and target devices. Step 4: Copy Completed! Proceed to verify device(s). Scroll to select "2. Compare", then press "OK" to start the verification process. Sequentially automates from Function 1, Copy to Function 2, Compare. Scroll to select "3. Copy+Compare", then press "OK" to start the automated duplication and verification process. User is responsible for verification of targets' quality. Testing a few completed targets in a mass production environment for quality control is recommended. There are 7 submenu modes. Please back up all important data before using this function....
Open the catalog to page 9Source Port is disabled for erasing. Go to 6.8.2 to enable source port erasing. Step 2: Enter function "4. Erase" Scroll to select "4. Erase”, then press "OK" to view the 7 erase modes. Step 3: Select an Erase Function. Here are a couple tips to see port details during erase: ⚫ Press “▲” or “▼” to view real-time status of each port. ⚫ Press “OK” to view the details of each port. Step 4: Erase Completed Here are a few tips to perform or stop an Erase job. ⚫ Press “Asynchronous Erase Button” to start a new Erase job. ⚫ Press “Asynchronous Erase Button” for 5 seconds to stop a single port. ⚫ Press...
Open the catalog to page 10erasure of the connected device(s). Scroll to select "4.4 DoD EraseComp", then press "OK" to start the erasing and verifying process. 4.5 7-Pass Erase This function will erase device(s) 7 times complying with DoD 5220.22-M(ECE) Standards. Scroll to select "4.5 7-Pass Erase", then press "OK" to start the erasing process. 4.6 Secure Erase This function erases the non-loadable areas complying with NIST 800-88 Standards. Scroll to select "4.6 Secure Erase ", then press "OK" to start the erasing process. Caution If Secure Erase process is interrupted, the device will be locked. Please execute again...
Open the catalog to page 11Step 1: Create an Update HDD Place a SDD/HDD to the duplicator. Select function "5.2.2 Create Update HDD". Step 2: Format BIOS HDD Click "OK" to format the BIOS hard disk. One FAT, 2GB partition will be formatted in HDD. That would reduce searching time and speed up firmware update. Caution The data saved in this HDD will be erased. Step 3: Download Firmware Connect the BIOS HDD to PC. Download the latest firmware from PC and save it to HDD. Unzip BIOS and save it to the root directory. Step 4: Enter "Update BIOS" Place the BIOS HDD into source port. Enter function "5.2.1 Update BIOS". Update...
Open the catalog to page 125.7 Unlock HDD This function will count the CRC64 value for the source port. The CRC64 value is an easy way to double check the source data is correct. User is responsible for verification of targets’ quality. Testing a few Caution completed targets in a mass production environment for quality control is recommended. 6. Setup 6.1 Copy Area There are 4 submenu modes. Scroll to select "6.1 Copy Area”, then press "OK.” Then scroll through to select one of the four copy methods. 6.1.1 System and Files Copies data and skips empty space. Only supports standardized formats. Scroll to select "System...
Open the catalog to page 136.1.2 All Partitions Copies all partitions and data, unallocated partitions not included. Scroll to select "All Partitions”, then press "OK" to save the copy method. The target device’s capacity must be equal to or larger than the source device’s capacity. Source 350GB of all Partitions along with its contents will be copied. 6.1.3 Whole HDD Copies all source data bit by bit. Scroll to select "Whole Device”, then press "OK" to save the copy method. Copies the whole source device, irrespective of content, format, partition or empty space. This mode does not analyze the data. Source All 500GB of...
Open the catalog to page 146.1.4 Percentage (%) Select percentage of source capacity to copy. Scroll to select "Percentage”, set the upper and lower %, then press "OK" to save the copy method. Source Only copies the selected area. 6.2 Shrink last NTFS on Copy This function can reduce the size of the last partition of an NTFS formatted hard disk. If the capacity of the source disk is larger than the target, but the actual data content does not exceed the capacity of the target, when the copy function is executed, enable this function to reduce the content of the last partition (must be NTFS) of the target in standard NTFS...
Open the catalog to page 1521 Pages
18 Pages
31 Pages
31 Pages
23 Pages
23 Pages
37 Pages
21 Pages
24 Pages
4 Pages
41 Pages
2 Pages
41 Pages