
NV-BM GT11 Series PCIE Duplicator and Sanitizer User Manual v A.15
Open the catalog to page 1Index Table
Open the catalog to page 2Product Disclaimer U-Reach is not accountable for any incidental or consequential damages, including, but not limited to property harm, loss of time or data from use of any U-Reach product, or any other damages attributable to product malfunction or failure of including without limitation, those attributed to reliance of the materials provided, costs of product replacement, loss of use, data or profits, delays or business interruptions, any principle of legal responsibility arising from or in reference to the use, overall performance, delays in servicing, or lack of ability to render service...
Open the catalog to page 3Important Notice • Carefully read the entire manual before operating. • Make sure the source device is correct and functioning. • Equal capacity of source and target is recommended for guaranteed data consistency. • Using the Copy+Compare function provides the most flawless duplication. • Damage incurred due to non-compliance with U-Reach operating instructions will void the warranty. • Store the equipment safely when not in use and keep out of the reach of children. • Please turn off duplicator before replacing sockets. • Never turn off the power while the firmware updates. • Use only approved,...
Open the catalog to page 4Updates system firmware Updates system firmware through the source or USB port. 5.2.2 Create Update Device Prepares firmware update device by formatting the device to a 2GB FAT partition. 5.3 System Info Displays system information such as controller, model number, software version, etc. 5.4.1 Load New Firmware 5.4.2 Burn FW→SSD Slot1 5.4 Burn SSD Firmware Begins firmware update for compatible SSDs. 5.4.3 Burn FW→SSD Slot2 5.4.4 Burn FW→SSD Slot3 5.4.5 Burn FW→All Slot 5.4.6 Show SSD Version 5.4.7 Power Off Time 5.5 Calc. CRC64 Calculates the CRC64 value of the source device. 6.1 Start-up Menu...
Open the catalog to page 6Only down/up buttons are disabled. Reboot system for setting to be in effect.
Open the catalog to page 8Front View USB port for Log Report Outputs and Firmware Updates. Control Buttons OK Button LCD Display SSD slot for saving Master Images. (on side) Back View Power Input Grounding Port Power Switch
Open the catalog to page 10Yellow: Powered Green: Pass LCD Configuration Number of Function Target Device Total Size The slowest Device Time elapsed and copy progress Copied processed size
Open the catalog to page 11Recommendation: Target device(s)' capacity must be equal to or larger than the source device capacity. Step 2: Connect source and target devices.Step 3: Proceed to copy. Scroll to select "1. Copy", then press "OK" to select which source to copy from. Scroll to select "1.1 Source Port" or select "1.2 Internal Storage", then press "OK" to start the duplication process. The number of working/connected targets will be displayed on the LCD. Press "OK" to start. The following information below states what is displayed on the LCD during duplication. Function Total Data Copied Slowest Copied Time & %...
Open the catalog to page 121.2 Internal Storage (Available when internal SSD is installed) Scroll to select “1. 2 Internal Storage”, then press “OK” to select which GOB Image to copy from the duplicator’s built-in storage device. The GOB Image is created through U-Reach’s proprietary software that is included with the duplicator or through the Image Manager (function 8 when an SSD is installed). 1. When “1.2 Internal Storage” is selected, the 1st port becomes a target port automatically (e.g. NV-BM600 will become a 1-6 duplicator). Please use the Caution duplicator carefully as the manufacturer will not be held responsible...
Open the catalog to page 13Scroll to select "3. 1 Source Port", then press "OK" to copy to and verify targets from the source port. 3.2 Internal Storage (Available when internalSSD is installed) Scroll to select "3. 2 Internal Storage" , then press "OK" to select which GOB Image to copy and verify from the duplicator's built-in storage device. The GOB Image is created through U-Reach's proprietary software that is included with the duplicator or through the Image Manager (function 8 when an SSD is installed). Scroll to select "4. Erase", then press "OK" to view the 6 submenus. This function erases the area on the connected...
Open the catalog to page 144.2 Full Erase (NIST Clear) Security level: High This function will erase all data per NIST 800-88 Standards to the connected device(s) by overwriting all bits of data with binary 0’s Scroll to select “4.2 Full Erase (NIST Clear)”, then press “OK” to start the erasing process. 4.3 DoD3 Pass Security level: High This function will erase all data per DoD 5220.22-M Standards of the connected device(s) with a 3-step process; Step 1: Overwrite all data with binary 0’s, Step 2: Overwrite all data with binary 1’s, Step 3: Overwrite all data with randomly generated binary 1’s and 0’s. The type of random...
Open the catalog to page 15Although Secure Erase/ Enhanced Secure Erase are commands of the SATA and NVMe specifications, not all devices support them. If non-compliant devices are encountered, the LCD will display “Not Support!” 5. Utility This menu will reveal submenus related to device information, system information and updates. Scroll to select “5. Utility”, then press “OK” to view the submenus. 5.1 Show Device Info This function will display basic information such as device model, name, capacity, device firmware version, power cycle, power-on hours, and temperature. Scroll to select “5.1 Show Device Info”, then press...
Open the catalog to page 16Connect a device to the source port. Scroll to select "5.2.2 Create Update Device”, then press "OK" to start the format process. This will format the device to a 2GB FAT32 Partition. Caution Any data on connected device will be erased or corrupted. Step2: Download Firmware. Connect this device to PC. Download the latest firmware provided by supplier’s technical support, unzip the BIOS firmware, then save it to the root directory in the device. Note Ensure that the device does not have any bad sectors. Step3: Proceed to update firmware. Connect this device to the source port. Scroll to select...
Open the catalog to page 1721 Pages
19 Pages
18 Pages
31 Pages
31 Pages
23 Pages
23 Pages
37 Pages
21 Pages
24 Pages
4 Pages
2 Pages
41 Pages