
MTS-SASN Series SATA/SAS Duplicator and Sanitizer User Manual
Open the catalog to page 1Product Disclaimer U-Reach is not accountable for any incidental or consequential damages, which includes, but is not constrained to property harm, loss of time or data from use of a U-Reach product, or any other damages attributable to product malfunction or failure (including without limitation, those attributable to: (1) reliance of the materials provided, (2) costs of product replacement, (3) loss of use, data or profits, (4) delays or business interruptions, (5) and any principle of legal responsibility, arising out of or in reference to the use or overall performance or from delays in servicing...
Open the catalog to page 3Important Notice • Carefully read the entire manual before operating. • Make sure the source device is correct and functioning. • Equal capacity of source and target is recommended for guaranteed data consistency. • Using the Copy +Compare function provides the most flawless duplication. • Damage incurred due to non-compliance with our operating instructions will void the warranty. • Store the equipment safely when not in use and keep out of the reach of children. • Please turn off duplicator before replacing the socket. • Never turn off the power while the firmware updating. • Use only approved,...
Open the catalog to page 4Front View Source Port Target Ports Fast Blue Key (Asynchronous Erase Button) Indication LED Yellow: Powering Green: Pass Red: Fail LCD Display Operation Buttons USB Port for BIOS Update and LOG Report Output Back View PC Link Grounding Port Power Switch and Power Suppl
Open the catalog to page 5The slowest Backward Cancel/Back Time elapsed and Copied processed size copy progress
Open the catalog to page 6Copies data and skips empty space. Only supports standard formats. 6.9.4 Skip Bad Sector at Erase Skips bad sectors during Erase.
Open the catalog to page 9Sets device power-up buffer time when tasks are initiated. Able to set from 5 to 99 seconds. Sets the amount of time the duplicator should wait for the device(s) to respond. Sets how many times the duplicator should try if there is no response from the device(s). Locks keys only allowing "OK/ESC" buttons to function. (System reboot is required) Creates watermark on the device(s) after erase job is completed. Allows user to select from UDMA2 to UDMA7. The UDMA7 is the fastest.
Open the catalog to page 10Step 1: Prepare source and target devices. The information below states what is displayed on the LCD during duplication. Function Total Data Copied Slowest Copied Time & % Port Data Step 4: Copy Completed! The quantity of passed or failed target device(s), the copied duration, and CRC64 will be displayed on the LCD after duplication completes. CRC64: During duplication, each port will simultaneously record written data and compare CRC64 between source and targets. The result will be conveyed with a green light (pass) or a red light (fail). Proceed to verify device(s). Scroll to select "2. Compare",...
Open the catalog to page 123. Copy+Compare Sequentially automates from Function 1, Copy to Function 2, Compare. Scroll to select "3. Copy+Compare", then press "OK" to start the automated duplication and verification process. Caution User is responsible for verification of targets’ quality. Testing a few completed targets in a mass production environment for quality control is recommended. 4. Erase There are 13 submenu modes. Caution Please back up all important data before using this function. Step 1: Connect device(s) for sanitizing. Note Source Port is disabled for erasing. Go to 6.9.2 to enable source port erasing....
Open the catalog to page 13Scroll to select "4.1. Quick Erase”, then press "OK" to start the erasing process. 4.2 Full Erase (NIST Clear) This function will erase all data per NIST 800-88 Standards on the connected device(s). Scroll to select "4.2 Full Erase (NIST Clear)”, then press "OK" to start the erasing process. 4.3 DoD3 Pass This function will erase all data per DoD 5220.22-M Standards on the connected device(s). Scroll to select "4.3 DoD3 Pass", then press "OK" to start the erasing process. 4.4 DoD3 Pass+Compare This function will erase all data per DoD 5220.22-M Standards, then compare erasure of the connected...
Open the catalog to page 144.9 US Army AR 380-19 This function will erase device(s) complying with Army Regulation 380-19 by the US Army. Scroll to select "4.9 US Army AR 380-19", then press "OK" to start the erasing process. 4.10 Sanitize Block Erase This function will erase the non-loadable areas of SAS SSD(s) complying with NIST 800-88 Standards. Scroll to select "4.10 Sanitize Block Erase ", then press "OK" to start the erasing process. Caution During the Sanitize Block Erase process, do not interrupt the erasure operation, as it may result in the hard drive being unreadable by the computer. You will need to complete...
Open the catalog to page 15Note The USB's format must be: FAT16 or FAT32. Step 2: Proceed to update firmware. Connect USB drive to the USB port in front of the duplicator. Scroll to select "5.2.1 Update BIOS", then press "OK" to start the firmware update process. The firmware update process may take longer than 5 minutes. Please do not disrupt power or process during BIOS update. If interrupted, the system will become useless. We will not be held responsible for any damages. Step 1: Prepare a device for update. Connect a device to the source port. Scroll to select "5.2.2 Create Update HDD", then press "OK" to start the...
Open the catalog to page 16This function scans device for any bad sectors by reading and writing two times. Scroll to select "5.5 Strict Verify HDD”, then press "OK" to initiate process. Then scroll through to view connected device(s) by port order. 5.6 Unlock HDD Unlocks the HDD that has not completed Secure Erase so that the HDD can continue to be used. 5.7 Calc. MD5 Value This function will count the MD5 value for the source port. The MD5 value is an easy way to double check the source data is correct. 5.8 Calc. SHA256 Value This function will count the SHA256 value for the source port. The SHA256 value is an easy way...
Open the catalog to page 1721 Pages
19 Pages
18 Pages
31 Pages
23 Pages
23 Pages
37 Pages
21 Pages
24 Pages
4 Pages
41 Pages
2 Pages
41 Pages