
Carry Series 1 to 2 SATA HDD/SSD Duplicator and Sanitizer User Manual v A.04
Open the catalog to page 1Index Table
Open the catalog to page 2Product Disclaimer U-Reach is not accountable for any incidental or consequential damages, including, but not limited to property harm, loss of time or data from use of any U-Reach product, or any other damages attributable to product malfunction or failure of including without limitation, those attributed to reliance of the materials provided, costs of product replacement, loss of use, data or profits, delays or business interruptions, any principle of legal responsibility arising from or in reference to the use, overall performance, delays in servicing, or lack of ability to render service...
Open the catalog to page 3Important Notice • Carefully read the entire manual before operating. • Make sure the source device is correct and functioning. • Equal capacity of source and target is recommended for guaranteed data consistency. • Using the Copy+Compare function provides the most flawless duplication. • Damage incurred due to non-compliance with our operating instructions will void the warranty. • Store the equipment safely when not in use and keep out of the reach of children. • Please turn off duplicator before replacing sockets. • Never turn off the power while the firmware updates. • Use only approved,...
Open the catalog to page 4Product Overview Hardware Red: Fail Flashing Green: Operating Remain Green: Pass Yellow: Powered UP: Backward OK: Confirm/OK DOWN: Forward ESC: Cancel/Back LCD configuration Total Size Target HDD Function Time Copy x1 0:11 41% Copy Progress % 2047M 860M Copied Processed Size (Target
Open the catalog to page 56.7.10 Stop Motor Time Auto running time after stopping motor from 1~20 seconds. 6.8 Restore Default Back to original manufacturer setting.
Open the catalog to page 9Step 1: Prepare source and target devices. Step 4: Copy Completed! The number of working/connected targets will be displayed on the LCD. Press "OK" to start.
Open the catalog to page 10Sequentially automates from Function 1, Copy to Function 2, Compare. Scroll to select "3. Copy+Compare", then press "OK" to start the automated duplication and verification process. Step 2: Enter function "4. Erase" Scroll to select "4. Erase", then press "OK" to view the 7 erase modes. Step 3: Select an Erase Function. Here are a couple tips to see port details during erase: • Press "▲" or "▼" to view real-time status of each port. • Press "OK" to view the details of each port. Step 4: Erase Completed Here are a few tips to perform or stop an Erase job. • Press "Asynchronous Erase Button" to...
Open the catalog to page 114.2 Full Erase This function will erase all data per NIST 800-88 Standards on the connected device(s). Scroll to select "4.2 Full Erase”, then press "OK" to start the erasing process. 4.3 DoD Erase This function will erase all data per DoD 5220.22-M Standards on the connected device(s). Scroll to select "4.3 DoD Erase", then press "OK" to start the erasing process. 4.4 DoD Erase Comp This function will erase all data per DoD 5220.22-M Standards, then compare erasure of the connected device(s). Scroll to select "4.4 DoD EraseComp", then press "OK" to start the erasing and verifying process. 4.5...
Open the catalog to page 12This menu contains submenus related to device information, system information and updates. Scroll to "5. Utility”, then press "OK" to view the submenus. 5.1 Show Disk Info This function will display basic information such as device model, name, capacity, etc… Scroll to select "5.1 Disk Info”, then press "OK" to view the connected device(s). Then scroll through to view connected device(s) by port number order. 5.2 Update System This function is to execute firmware updating of system. You can follow the following steps to update the system firmware. Step 1: Create an Update HDD Place an SDD/HDD...
Open the catalog to page 135.4 Get Checksum This function will Calculates the CRC16 value of the HDD. 6. Setup 6.1 Start-up Menu This function allows user to select the default function to display during equipment initialization. Scroll to select "6.1 Start-up Menu”, then press "OK.” Then scroll through the available menus for startup. 6.2 Copy Area There are 4 submenu modes. Scroll to select "6.2 Copy Area”, then press "OK.” Then scroll through to select one of the four copy methods. ⚫ Selecting the Proper Copy Modes Example: There are two defined partitions in a 500GB device. The charts below illustrate what portion...
Open the catalog to page 14⚫ Copy and Compare Preparations Please consider the following settings before proceeding with copy or compare: - 6.2 Copy Area - 6.4 Skip Errors - 6.7.1 Unknown Format Using appropriate copy modes can greatly reduce operation time and increase efficiency. There are four copy modes with different copy methods. 6.2.1 System and Files Copies data and skips empty space. Only supports standardized formats. Scroll to select "System and Files”, then press "OK" to save the copy method. Allows user to copy source device’s System and Files, instead of the entire device. The system will analyze the source...
Open the catalog to page 15The target device’s capacity must be equal to or larger than the source device’s capacity. Source 350GB of all Partitions along with its contents will be copied. 6.2.3 Whole HDD Copies all source data bit by bit. Scroll to select "Whole Device”, then press "OK" to save the copy method. Copies the whole source device, irrespective of content, format, partition or empty space. This mode does not analyze the data. Source All 500GB of data will be copied. 6.2.4 Percentage (%) Select percentage of source capacity to copy. Scroll to select "Percentage”, set the upper and lower %, then press "OK" to...
Open the catalog to page 16the copy method. Source Only copies the selected area. 6.3 Copy GPT Backup Area Enabling this function allows the duplicator to copy from big capacity device to small capacity device(s). partition size of the source HDD must be smaller than target Note The capacity. GPT Index Partition Disabling function “6.3 Copy GPT Backup Area” will force the duplicator to ignore this area. GPT Backup Area If function is disabled, the target HDD will reconstruct the GPT Backup Area by Windows system. It may require the HDD to restart to work. 6.4 Skip Errors Skips bad sectors during Copy/ Compare/ Erase. 1
Open the catalog to page 1719 Pages
18 Pages
31 Pages
31 Pages
23 Pages
23 Pages
37 Pages
21 Pages
24 Pages
4 Pages
41 Pages
2 Pages
41 Pages