Catalogs >
TWK-ELEKTRONIK GmbH >
Magnetostrictive displacement transducer MSC

Magnetostrictive displacement transducer MSC
3Pages

Catalog excerpts

Magnetostrictive displacement transducer MSC - 1

MAGNOSENS Magnetostrictive Displacement Transducers Model series MPC / MSC: Analogue output or start/stop ■ MPC model: Profile version ■ MSC model: Rod version ■ Measuring strokes from 50 to 2500 mm (analogue) to 7600 mm (start / stop) ■ Contactless, robust system ■ Infinite resolution ■ Linearity < 0.02 % ■ Measurement signals 0(4) ... 20 mA, 0 ... 10 V, ± 10 V or start/stop signal ■ Protection type up to IP 68 ■ Operating temperature range - 40 °C ... + 80 °C, optionally up to 100°C for start/stop version ■ Pressure stability up to 350 bar Structure and operation The displacement transducers operate according to the principle of run time measurement between two points of a magnetostrictive waveguide. One point is determined by a moveable position magnet, whose distance from the null point corresponds to the section to be measured. The run time of an emitted impulse is directly proportionate to this section. Conversion to an analogue measuring signal takes place in the downstream electronics. The waveguide is housed in a pressure-resistant stainless steel tube or extruded profile. To the rear of this is a die-cast aluminium housing containing the electronics in SMD technology. Electrical connection is implemented via a circular connector. In the rod version, the position magnet is located in a ring, which is guided over the rod without contact. In the profile version, it is located either in a slider, which is linked to the moving part of the machine via a ball joint, or it moves as a liftable position magnet, without wear, over the profile. Standard measuring strokes: Analogue and start/stop: □ Up to 1000 mm in 50 mm steps Analogue output: □ Up to 2500 mm in 250 mm steps Start/stop: □ Up to 5000 (profile) / 7600 (rod) mm in 250 mm steps

Open the catalog to page 1

Magnetostrictive displacement transducer MSC - 2

Technical data Order code format 24 VDC (+20 / -15%) 100 mA typical Analogue: Practically infinite Start/stop: 0.1; 0.01; 0.005 mm depending on evaluation electronics < ± 0.02 % (min. ± 50 pm) < ± 0.001 % (min. ± 2.5 pm) < 4 pm Analogue: > 1 kHz, start/stop: depending on evaluation electronics and meas. length < 40 ppm / °C - 40 °C to + 80 °C Optionally up to 100 °C 100 g to IEC Standard 68-2-27 15 g / 10 to 2000 Hz to IEC Standard 68-2-6 IP 65 IP 67, IP 68 for cable outlet 0...10 VDC / - 10 ... + 10 VDC > 5 kQ RS422 differential signal 6-pin connector M16 Die-cast zinc, nickel-plated...

Open the catalog to page 2

Magnetostrictive displacement transducer MSC - 3

Magnetostrictive Displacement Transducers MPC / MSC Metal connector Sensor head With measuring strokes of 1000 mm and over, mechanical rod support is recommended. The sensor’s fastening should be manufactured from non-magnetic materials (e.g.: brass, plastic). Note installation instruction MWA10318 on installation in magnetisable materials. Position ring Measuring range Installation zone Damping zone Option: Cable outlet Model: MSC (profile version) Front ball joint PS02 Central ball joint PS01 Threaded connection Sensor head Metal connector Liftable position magnet PR03 44 Installation...

Open the catalog to page 3