Catalogs >
TWK-ELEKTRONIK GmbH >
Inductive linear transducers IW120

Inductive linear transducers IW120
4Pages

Catalog excerpts

■ Contactless, robust system ■ Infinite resolution ■ No hysteresis ■ Linearity 0.5 % or 0.25 % ■ Protection type IP 66 (with cable IP 68) ■ Supply and signal processing through external modules ■ Housing material: Stainless steel (1.4305) Plunger Material: nickel-iron (stainless) Design and function The linear transducers operate according to the differential throttle principle (inductive half-bridges). They consist of two coils which are impermeably cast into a Mu-metal cylinder, where they are protected from vibrations. On displacement through the hollow coil body, a Mu-metal plunger leads to a change in the induction direction in both coils. The linear transducers are designed for an oscillator frequency of 10 kHz. The supply and signal processing are carried out by external modules. Standard measuring strokes: 12, 24, 40, 60, 100, 150, 200 mm Note: Unless otherwise specified, the values apply at an ambient temperature of +20 °C and on use of the transducer with oscillator/demodulator OD15 according to data sheet OD 10220. The housings and plungers are assigned to each other and bear the same serial number. They must not be interchanged. Technical data ■ Linearity: ■ Operating temp. range □ Standard: □ Connector des. form: ■ Shock resistance: ■ Vibration resistance: ■ Protection type: ■ Further data: < 0.5 % or < 0.25 % - 55 °C to + 100 °C - 40 °C to + 85 °C 250 g SRS 20 - 2000 Hz 20 g rms (50 g peak) 20 - 2000 Hz IP 66 See table on page 2 and 3 TWK-ELEKTRONIK GmbH ■ PB. 10 50 63 ■ D-40041 Dusseldorf ■ Tel.: +49/211/63 20 67 ■ Fax: +49/211/63 77 05 ■ info@twk.de ■

Open the catalog to page 1

Standard design form: Electrical connections via Kynar strands, 300 mm long. Variants and accessories Design S: Mating connector: Design form T: Design form KV: Design form KF: Design form KH: Connector, 3-pin with gold-plated contacts Binder female coupling connector 681 (IP 40). Binder female coupling connector 723M (IP 66), metal housing with earth slip ring, to be ordered separately. Gauge version with return spring (measuring stroke up to 100 mm available). With ball joint on the plunger. With special plunger guide and ball joint on the plunger. With ball joint on the housing. Model...

Open the catalog to page 2

Inductive linear transducer model series IW 120 Standard-design form with kynar-strands, 300 mm long Design form with return spring Measuring stroke up to 100 mm Design form T dimensions IW 120 /...T B1 BM Init. stroke Sec. stroke FM Fc = plunger in centre position (electr. zero). = plunger fully extended. = spring pre-tension with BM. = constant spring rate. Design form with ball joints 27 guide sleeve Design form with connector (ball joint optional ) Design form with cable (ball joint optional) L2 Width across flats 17

Open the catalog to page 3

Inductive linear transducer model series IW 120 Design form with axial cable (not usable with KH) Visible embedding compound (black) Design form with radial cable (not usable with KH) Visible embedding compound (black) Design form with radial cable and ball joint (KH) L2 +25 Assembly block MB 12 (nickel-plated brass) (to be ordered separately) Weight: 36 g Two 25 mm-long allen head bolts M4 are supplied

Open the catalog to page 4

Inductive linear transducers IW120 4Pages

Catalog excerpts

All TWK-ELEKTRONIK GmbH catalogs and technical brochures

Inductive linear transducers IW120
4Pages