Catalogs >
TSUBAKI KABELSCHLEPP >
ROBOTRAX System

ROBOTRAX System
10Pages

Catalog excerpts

ROBOTRAX® System Trademarks are legally protected for the TSUBAKI KABELSCHLEPP GmbH as a national or international registration in the following countries: tsubaki-kabelschlepp.com/trademarks Subject to change without notice. Cable carrier for 3D movements

Open the catalog to page 1

ROBOTRAX® System 6 Protective covers or heat shields made from different materials are available for different environmental conditions 7 Quick-release bracket for fixing and continuation 8 Strain relief with LineFix clamps 9 Protection against hard impacts, excessive abrasion and premature wear as well as limitation of the bending radius through protector Fast cable laying by simply pressing in the cables (R040 – R100) Strain relief for secure fixing of the cables 4 Open design – Fast cable laying as the cables are simply pressed in – Easy checking of all cables 5 Special plastic for long...

Open the catalog to page 2

Radial link rotation on 1 m length [°] Radial link rotation on 1 m length [°] MT series XLT series ROBOTRAX® System Additio- Cablenal load dmax ≤ [kg/m] [mm] Values in [ ] apply when using protectors Subject to change without notice. Additio- Cablenal load dmax ≤ [kg/m] [mm] S/SX-Tubes series Accessories TRAXLINE® Opening variant Values in [ ] apply when using protectors LS/LSX series Opening variant

Open the catalog to page 3

Subject to change without notice. S/SX-Tubes series LS/LSX series ROBOTRAX® System

Open the catalog to page 4

ROBOTRAX® System | Design principle The basic structure of ROBOTRAX® consists of plastic links. These have spherical snap-on connections on both sides. This allows the individual links to be snapped together to form a cable carrier. Protectors ensure that the bending radius does not fall below the minimum in any direction. The links can be rotated in the radial direction (see table values). The cables can be separated in three chambers. LS/LSX series S/SX-Tubes series Radial rotation possible on 1 m length [°] Values in [] apply when using protectors *We recommend a maximum cable diameter...

Open the catalog to page 5

ROBOTRAX® System | Design principle ROBOTRAX® System Chain links with crossbars The basic construction is similar to the ROBOTRAX® types with single part design. Swiveling crossbars with snap locks make it easy to open and safely close the cable carrier. In addition, the three chambers can be divided horizontally and vertically by a divider module for precisely separating cables and hoses. LS/LSX series Dimensions and order Radial rotation possible on 1 m length [°] Subject to change without notice. Values in [] apply when using protectors Order example Calculating the cable carrier length...

Open the catalog to page 6

ROBOTRAX® System | Design principle Fast movements of the robot arms generate high accelerations and therefore high tensile forces on the cable carrier. To transfer these tensile forces, ROBOTRAX® has a hole at the center of each chain link through which the steel cable is pulled. This steel cable takes on the function of force transmission. The steel cable is fixed with a clamping piece on one side. ROBOTRAX® permits accelerations up to 10 g. The clamping piece can be used to easily set the chain links to the desired tension and adjust them at any time. Long service life of the cables and...

Open the catalog to page 7

ROBOTRAX® System | System components Strain relief for cable ties (available for all types) For secure fixing of the cables. The strain relief can be used on either end. Please state the desired type series and quantity when ordering. XLT series S/SX-Tubes series Accessories Subject to change without notice. (for types R075, R085, R100 and R140X) Secure cable fixing, gentle on the cables. Multi-layer cable fixing is also possible with double and triple LineFix® clamps. Several systems can be installed in sequence. LineFix® strain reliefs – see page 904. LS/LSX series Please state the...

Open the catalog to page 8

ROBOTRAX® System | System components (for types R040, R056, R075, R085 and R100) Please state the number, robot type and type series when ordering. PBU: With fast movement sequences and large work envelopes, the relatively long carriers knock against the robot arm. The repeated impact significantly reduces the service life of the cable carrier and the cables within, and the entire system can fail. Downtimes cause high costs and problems in the manufacturing process – so they have to be avoided. » Compact design: fewer interfering contours and lower risk of collision » Maximum flexibility...

Open the catalog to page 9

ROBOTRAX® System | System components Turntable for quick-release bracket Please state the desired type series and quantity when ordering. ROBOTRAX® System Sample image LS/LSX series Coil spring for quick-release bracket If the quick-release bracket is mounted on a coil spring, it can move elastically in all directions, deflect in 3 dimensions and spring back. Please state the desired type series and quantity when ordering. Subject to change without notice. S/SX-Tubes series One additional degree of freedom on the attachments points. When mounted on a turntable, the quick-relea

Open the catalog to page 10

ROBOTRAX System 10Pages

Catalog excerpts

All TSUBAKI KABELSCHLEPP catalogs and technical brochures

ROBOTRAX System
10Pages