QUANTUM
8Pages

Add to favorites

Catalog excerpts

VARIO LINE BASIC LINEPLUS BASIC LINE

Open the catalog to page 1

Inside heights Light, extremely quiet and low-vibration for high speeds and accelerations* *** Tested: Q040.77.RE-70-1000 by the Fraunhofer Institute, travel speed V1 = 0.2 m/s and V2 = 0.9 m/s *** Tested: Q060.100.100 by TÜV Rheinland. The measurement area sound pressure level was measured at a distance of 0.5 m for uniform and jerky movement. C-Rail for strain relief elements or strain relief comb Universal connectors (UMB) Extremely low-noise and low-vibration operation Aluminum stays available in 1 mm width sections Plastic stays available in 8 or 16 mm width sections Large choice of...

Open the catalog to page 2

Selection BASIC LINE ■ Available in 8 or 16 mm width sections (plastic stays) Dynamics of unsupported arrangement Maximum travel length in m Travel speed vmax in m/s Travel acceleration amax in m/s2 * with stay variant RE Use our free project planning service. VARIO LINE ■ Available in 1 mm width sections (aluminum stays) Stay variants Frame stay RS made of aluminum Standard design – Q 060, Q 080, Q 100 For lightweight to medium loads. Opening options: Outside/Inside: can be opened quickly and easily simply by rotating the stays through 90°. Frame stay RV made of aluminum Reinforced design...

Open the catalog to page 3

Selection BASIC LINE Inside heights Bend radius and pitch Type Q 040 Q 060 Q 080 Q 100 Load diagram for length with permissible (desired) sag LD depending on the additional load 12.0 Length with permissible sag LD and travel length LS LS "Plastic designs" In the case of long travel lengths, the cable carriers are placed in a guide channel with the upper trough gliding on the lower trough (see page 375). We are at your service to advise on these applications. 0 1.5 2.0 0.5 1.0 Length with permitted sag LD in m Example of ordering Cable Carrier Divider system 1540 Chain length Lk in mm...

Open the catalog to page 4

Selection BASIC LINE Standard mounting distances of the divider systems: Q 040, Q 060: on every 6th pitch division Q 080, Q 100: on every 8th pitch division In the standard version, the dividers are movable. In the case of plastic stays (stay variant RE), the dividers can also be mounted fixed (note the mounting distances). Guide channels ➤ from page 375 Strain relief devices ➤ from page 381 Divider system TS 1 with continuous height subdivision made of aluminum Standard mounting distances of the divider systems: Q 040, Q 060: on every 6th pitch division Q 080, Q 100: on every 8th pitch...

Open the catalog to page 5

Selection BASIC LINE * When using plastic partitions A) Only fixed mounting of the divider is possible, and at 8 mm intervals (also see mounting version B in Chapter ME/MK). B) The dividers are fixed by the partitions, the complete divider system is movable. Inside widths Standard mounting distances of the divider systems: Q 040, Q 060: on every 6th pitch division Q 080, Q 100: on every 8th pitch division Dimensions of the plastic partitions for TS 3 SZ 4 Aluminum partitions in 1 mm width sections are also available. When using partitions with ax > 112 mm there should be an additional...

Open the catalog to page 6

UMB (Universal Mounting Brackets) made of plastic (Q 040/060) or aluminum (Q 080/100) Inside widths The dimensions of the fixed point and driver connections are identical. The connecting elements make the the last 3 pitch divisions at both ends of each sideband immobile. When ordering please specify the connection type FU/MU (see ordering key on page 419). Connection dimensions: Type Q 040 Q 060 Q 080 Q 100 Strain relief devices Strain relief comb made of aluminum on one side (QUANTUM 040, 060) The cables can be fixed securely and simply using the optional strain relief combs. The strain...

Open the catalog to page 7

Selection BASIC LINE Inside heights Strain relief combs made of plastic on both sides (QUANTUM 060) The cables can be fixed securely and simply using the optional strain relief combs. The strain relief combs are installed between the UMBs, and do not need to be bolted on separately or mounted on a C-Rail. Please state on the order whether strain relief combs are needed. Inside widths nZ = Number of teeth on one side of the comb * on request ■ Both-sided strain relief comb The optional C-rails are fixed by means of the universal mounting brackets and do not have to be screwed separately....

Open the catalog to page 8

QUANTUM 8Pages

Catalog excerpts

All TSUBAKI KABELSCHLEPP catalogs and technical brochures

QUANTUM
8Pages