Group: TRELLEBORG
Catalog excerpts
Offshore Bearing Systems Trelleborg Ridderkerk BV
Open the catalog to page 1To supply products to the Offshore Industry is challenging for any supplier. Products must be thoroughly and rigorously designed, manufactured, tested and documented. Often the requirements push the scope of current technology, the lead times are short and the delivery times are critical. Clients must have complete confidence in your ability to perform under these conditions. Trelleborg Ridderkerk is a leading global supplier of elastomeric bearing systems to major offshore projects. Each of these products is designed to perform to the client’s specified operating criteria. We are focused...
Open the catalog to page 2Jack-ups are provided with jacking systems for lifting and lowering the platform on the legs. Since years Trelleborg Ridderkerk designs and supplies rubber shock pads for these jacking systems. The shock pads have to absorb loads in combination with relative low compression stiffness. Compared to ordinary steel-rubber laminated bearings, shock pads are built up with relative thick rubber layers. In order to monitor the loads during the jacking operations we have developed shock pads with an integrated electronic load cell. Shock pads for jack-ups
Open the catalog to page 3Floating Production Storage and Offloading Facilities (FPSOs) are a workhorse of the offshore industry. Their service requirements include multidirectional loads transferred between the hull and topside modules as a result of wave action. The module support bearings must be able to resist large alternating movements in all three directions and large rotational movements in line with the FPSOs longitudinal axis. Trelleborg Ridderkerk designs and manufactures support bearings to match these exacting requirements. Module Support Bearings for FPSOs In 2003, Trelleborg Ridderkerk won the order...
Open the catalog to page 4Trelleborg Ridderkerk used its rich experience in elastomeric bearings for bridges and shock pads for platforms to design the special module support bearings. In total 3 types have been designed for the FPSO SeaRose, the so called B01, B02 and B03. The heaviest of these elements is close to ten tonnes in weight and can withstand a vertical load of up to 10,000 kN and a horizontal load of up to 3,500 kN. The design is based on a combination of rubber and steel to compensate a displacement of 75 millimetres. All bearings are steel plate reinforced in order to keep the stresses to an...
Open the catalog to page 5Andre anti-vibration mounts Since the early 1970’s Andre have utilised their expertise and experience to provide AVMs world-wide to many of the major gas turbine, generator, compressor and pump unit manufacturers for the isolation of structures from potentially damaging machine-borne vibration. Applications cover oil and gas exploration and production platforms, FPSOs, accommadation modules and helidecks. Andre AVMs are custom designed and consist of elastomeric bearing units located under the support skid. Design Features • Natural frequency of the isolated skid: Typically within the...
Open the catalog to page 6Leg Mating Units (LMUs) and Deck Support Units (DSUs) are a critical part of the floatover process, one of the key installation methods for offshore constructions. During a floatover a deck is transported from the fabrication site and installed onto a pre-installed jacket. The decks typically weigh several thousand tonnes and this load has to be transferred to the lower structure in a controlled and progressive process. DSUs are applied between the deck load to the pre-installed jacket. Leg Mating and Deck Support Units The heart of the LMUs or DSUs is the load absorbing elastomeric units....
Open the catalog to page 7Sliding bearings for Sakhalin II PA-A Molikpaq Tie In Project Policy quality, environment, safety and health Photograph by courtesy of Shell International Ltd. Trelleborg Ridderkerk BV Verlengde Kerkweg 15, 2985 AZ Ridderkerk PO Box 4007, 2980 GA Ridderkerk, The Netherlands Tel: +31 180 49 55 55 Fax : +31 180 43 30 80 ridderkerk@trelleborg.com www.trelleborg.com/ridderkerk The policy of Trelleborg Ridderkerk BV is to design, produce and deliver rubber products which are in accordance with the customers’ requests, needs and expectations. Our policy is based on the Trelleborg Group policy...
Open the catalog to page 8All Trelleborg Infrastructure catalogs and technical brochures
-
Inflatable seals
4 Pages
-
More Information on Tunnel Seals
12 Pages
-
Gina Seals
14 Pages
-
Swing back safety barrier
4 Pages
-
Anti Vibration Mounts
2 Pages
-
Leg Can Systems
4 Pages
-
Rubstrips
6 Pages
-
ENERGY
14 Pages
-
Dredging & Marine products
2 Pages
-
Offshore Bearing Systems
8 Pages
-
Company profile
8 Pages
-
Teguflex
38 Pages
-
Lifting bags
5 Pages
-
Inflatable pipe plugs
20 Pages
-
Offshore Grout Seals
4 Pages
-
Dredging Hoses Ede
20 Pages
-
Seismic Transflex Joints
4 Pages
-
Pot Bearings
8 Pages
-
Gina Gasket
14 Pages
-
Omega seals
17 Pages
-
Injectable waterstops
17 Pages
-
Waterstops
26 Pages
-
Andre Structural bearings
4 Pages
-
Rubber Expansion Joints
17 Pages
-
Teguflex FFL
2 Pages
-
Teguflex W
2 Pages
-
Elastomeric Bridge Bearings
4 Pages
Archived catalogs
-
Trelleborg - Shipfenders catalog
11 Pages
-
COMPANY BROCHURE
6 Pages