QUICK LOAD™ Liners & AutoLength™ Pins
4Pages

Issued March 2018 • Index No. QLL/1.3 MIG (GMAW) Welding Consumables Quick Specs Applications Automotive Shipbuilding Heavy Equipment Fabrication Manufacturing Compatible With TOUGH GUN™ Robotic MIG Guns (CA3 & TA3) TOUGH GUN™ Automatic MIG Guns (MA1) Bernard™ BTB Semi-Automatic MIG Guns Bernard™ TGX™ Semi-Automatic MIG Guns* Bernard™ Clean Air™ Semi-Automatic MIG Guns *AutoLength Pins not available with TGX MIG Guns QUICK LOAD™ Liners require less than half the time and effort to replace compared to conventional liners. This innovative front-loading liner is a two-piece system with the retainer installed inside the power pin on first use, and is compatible with Tregaskiss™ TOUGH GUN™ Robotic and Automatic Air-Cooled MIG Guns, and Bernard™ BTB MIG Guns. During the initial installation of the QUICK LOAD Liner, the retainer remains mated with the liner while it is installed through the rear of the MIG gun like a conventional liner. Subsequent liner replacements occur through the front of the gun without a need to replace the retainer. Two-piece system with retainer installed inside the power pin on first use Available for TOUGH GUN™ Robotic and Automatic MIG Guns in lengths of up to 15 feet and Bernard™ Semi-Automatic MIG Guns in lengths of up to 25 feet REDUCE UNEXPECTED DOWNTIME & SCRAP COST Reload from the front in less than half the time Increase efficiency and reduce downtime and consumable cost Spring-loaded module allows for up to one-inch (2.54 cm) forgiveness if the liner is too short QUICK LOAD Liner AutoLength™ System Pair your QUICK LOAD Liner with an AutoLength Pin to reap the benefits of the revolutionary QUICK LOAD Liner AutoLength System. Minimize downtime, wire feeding and quality issues commonly associated with short liner length. • Reduces issues caused by short liners • Decreases burn-backs caused by misalignment between the liner and contact tip • Accommodates liner movement during welding • Improves wire feeding by enhancing wire alignment with the contact tip Tregaskiss 2570 North Talbot Road Windsor, Ontario N0R 1L0 Canada Phone: 1-855-MIGWELD (644-9353) (us & Canada) +1-519-737-3000 (International) Fax: 519-737-1530 For more information, visit us at

Select your wire size and gun length in the table below to find which QUICK LOAD Liner part number is needed for your application. Compatible with Tregaskiss TOUGH GUN Robotic and Automatic MIG Guns and Bernard BTB, TGX and Clean Air Semi-Automatic MIG Guns **Compatibie with most Tweco® MIG Guns Euro 425-820E for 0.030" - 0.045" wire (Replaces Power Pin 425-20E) 425-920E for 0.052" - 3/32" wire (Replaces Power Pin 425-20E) Fronius® 214-817 for 0.030" - 0.045" wire (Replaces Power Pin 214-17) 214-841 for 0.030" - 0.045" wire (Replaces Power Pin 214-41) 214-917 for 0.052" - 3/32" wire...

AutoLength™ Pins (Continued) AutoLength Pins – For Semi-Automatic Applications Euro 425-820 for 0.030" - 0.045" wire (Replaces Power Pin 425-20) 425-920 for 0.052" - 3/32" wire (Replaces Power Pin 425-20) for 0.030" - 0.045" wire (Replaces Power Pin 214-17) for 0.030" - 0.045" wire (Replaces Power Pin 214-41) for 0.052" - 3/32" wire (Replaces Power Pin 214-17) for 0.052" - 3/32" wire (Replaces Power Pin 214-41) for 0.030" - 0.045" wire (Replaces Power Pin 214-1) for 0.030" – 0.045" wire (replaces Power Pin 214-6-116) for 0.052" - 3/32" wire (Replaces Power Pin 214-1) for 0.052" – 1/16" wire...

Installation and Replacement (Continued) QUICK LOAD Liner with AutoLength Pin How to Install the AutoLength Pin and QUICK LOAD Liner 1. Remove the gun from the wire feeding unit. 2. Remove the current power pin from the gun. 3. Replace power pin with an AutoLength Pin. Torque to 18-ft./lbs. 4. Feed the QUICK LOAD Liner through the FRONT of the gun until it engages with the retainer inside the AutoLength Pin. 5. Push the QUICK LOAD Liner into the gun until the liner will not go forward any further. Hold it in place (the liner will be pushed in by approximately 1 additional inch) and trim as...