- Catalogs
- TRANSMILLE
- TRANSMILLE 3010A PRECISION MULTIPRODUCT CALIBRATOR
TRANSMILLE 3010A PRECISION MULTIPRODUCT CALIBRATOR
TRANSMILLE 3010A PRECISION MULTIPRODUCT CALIBRATOR
The Transmille 3010A Precision Multiproduct Calibrator requires a warm-up time of up to 20 minutes and supports standard USB interfaces, with optional GPIB and RS232 interfaces. It operates within a temperature range of 0°C to 50°C and can be stored between -5°C and +60°C. The device functions at altitudes up to 3000m and can be transported at altitudes up to 12000m. It must be earthed for EMC and safety compliance, supports line voltages of 110V or 230V at 50Hz to 60Hz, and consumes 55 Watts in standby and 400 Watts maximum. It includes safety sockets and a backlit display with a resolution of 240 x 64 dots.
Accuracy details are provided for various voltage ranges, with a maximum burden current of 50mA and typical output resistance of 50 Ohms. Safety features include automatic standby for voltages over 20V and audible warnings for high voltage outputs. Specifications apply within TCal ± 5°C.
Accuracy is outlined for current ranges from 0-202µA to 20.2-30A, with compliance voltage protection up to 150V. Stability is detailed for various time frames, and specifications apply to loads less than 10% of the maximum burden voltage. Sufficient 'off' periods are necessary to prevent overheating.
Frequency ranges from 10Hz to 1MHz are covered, with accuracy details for each range. High voltage safety includes automatic standby and audible warnings. Specifications apply at TCal ± 5°C.
Accuracy details are provided for current ranges from 20-202µA to 2-30A, with frequency ranges from 10Hz to 1kHz. Stability is detailed for various time frames, and managing inductive loads is important to prevent exceeding the maximum burden voltage.
Safety, operational conditions, and adherence to specified load and temperature conditions are crucial for accurate performance. Specifications may change due to continuous development.
The document covers specifications for various measurement options including ACI, frequency, DC resistance, capacitance, simulated resistance, inductance, DC power, AC power, DDS power, and oscilloscope calibration. Specifications are subject to change.
Exceeding the maximum compliance voltage when driving inductive loads will cause the calibrator to trip into standby. Specifications apply at TCal ± 5°C.
Frequency accuracy is detailed for ranges from 1Hz to 10MHz. Specifications apply at TCal ± 5°C.
High accuracy is achieved using passive standard resistors. Specifications include total accuracy for various resistance ranges. Specifications apply at TCal ± 5°C.
Calibrated at the terminals, specifications cover ranges from 1nF to 10µF. Specifications apply at TCal ± 5°C.
Accuracy specifications are provided, with performance affected by measurement methods. Specifications apply at TCal ± 5°C.
Specifications cover ranges from 1mH to 10H, with accuracy relative to calibration standards. Specifications apply at TCal ± 5°C.
DC power specifications include voltage and current ranges, while AC power specifications include frequency range and phase specifications. High voltage safety features are included. Specifications apply at TCal ± 5°C.
Harmonic specifications are provided for user-defined waveforms. Specifications apply at TCal ± 5°C.
Specifications for amplitude and timebase calibration are provided, with high voltage safety features. Specifications apply at TCal ± 5°C.
- Time Division Settings: Ranges from 10ns/Div to 5s/Div with specific sequence options. Waveshape is a comb below 100ns and a sine wave above 100ns.
- Oscillator: Internal Crystal TCXO with output through a front BNC terminal.
- Timebase Deviation: Deviation range is ±10% in 0.001% steps.
- Levelled Sweep: Sweep range from 5MHz to 350MHz or 600MHz, depending on the option.
- Frequency and Level Accuracy: Frequency accuracy ranges from 27 ppm to 36 ppm, while level accuracy ranges from 0.4% to 0.7%.
- Fast Rise Output: Rise/fall time is typically 1ns, with a maximum of 1.5ns.
PRT Simulation Option
- General Specifications: Resistance values range from -100°C to +800°C.
- Accuracy: Relative accuracy to calibration standards is consistent across different temperature ranges.
Variable PRT Output
- PRT Type and Range: Covers a range from -200°C to 800°C.
- Connection and Measurement: Utilizes a 2-wire connection with specific requirements for terminal voltage and current input.
General Notes: Specifications apply at TCal ± 5°C, with allowances for deviations outside this range. Specifications are subject to change due to continuous development.
Catalog excerpts
OUTPUT CONTROL LiliUfr LlliLiU high current mjxiuarv terming
Open the catalog to page 1
3010A EXTENDED SPECIFICATIONS General Specifications TRANSMILLE LTD Due to continuous development specifications may be subject to change. 3010A Extended Specifications General Specifications : V1.81 www.T l"ansmille.com
Open the catalog to page 2
1 year Total Accuracy Specifications at Tcal ±5°C & Range Parameters Range Stability (Accuracy relative to calibration Standards) Range Notes Note 1: Allowance must be made for output resistance when driving Into a load. Note 2: Limited by 50 Ohm output impedance. Note 3 : Internally adjustable from 2mA to 30mA - Factory set to 20mA as standard. For safety the trip is controlled by a fail-safe circuit independant of the processor which shuts the high voltage output off in the event of an overload. Note 4: Typical RMS noise figures at 50% of full scale, bandwidth 1Hz to 10Hz. High Voltage Safety...
Open the catalog to page 3
1 year Total Accuracy Specifications at TCal ±5°C & Range Parameters Range Stability (Accuracy relative to calibration Standards) Range Notes Note 1 : Typical RMS noise figures at 50% of full scale. Note 2 : Power & temperature sensor on 30A range - microprocessor monitors & protects from overheating. Higher resistance loads allow a longer ON period. See graphs 1 and 2 for details. Note 3 : Specifications apply to loads of less than 10% of the maximum burden voltage. Note 4: Zero or floor allowance. Specifications apply at TCal ± 5°C Outside this range an allowance of 0.18 x 1 Year Spec. per...
Open the catalog to page 4
Time (Minutes) Current (Amps) Measurement Conditions : Ambient Temperature 20'C, Mains Voltage 230V, Mains Frequency 50Hz Allow at least 7 minutes 'off' period between current output Shorter periods will reduce the output time availiable. A higher ohmic value load (for example, a 0.1R Shunt) allows greater output time as more heat is dissapated within the shunt / load. With lower loads more heat is dissapated within the instrument, reducing output time Into a 0.1R Load outputs of up to 20A are available for periods of greater than 30 minutes continously, considerations of self heating of the...
Open the catalog to page 5
1 year Total Accuracy Specifications at TCal ±5°C & Range Parameters Range Stability (Accuracy relative to calibration Standards) All specifications apply from 10% of full scale. 5 AC Frequency Accuracy : 30ppm Notes Note 1: Current limited by 50 ohms output resistance. Note 2 : Internally adjustable from 2mA to 30mA - Factory set to 20mA as standard For safety the trip is controlled by a fail-safe circuit independant of the processor which shuts the high voltage output off in the event of an overload. Note 3 : Frequency and voltage combinations are limited. Note 4 : Specifications...
Open the catalog to page 6
2 Wire output / Remote sensing not available. Maximum floating voltage : 100V. Isolation : Floating or grounded selection available as standard. Specifications apply at TCal ± 5°C. Outside this range an allowance of 0.18 x 1 Year Spec. per °C should be added. High Voltage Safety High voltage output is ramped to allow instruments under test to auto-range. Standby is automatically activated when setting voltages greater than 20V or 200V from a lower voltage. Standby is automatically selected for high voltage (>20V) after 20 minutes on the same setting for frequencies up to 5kHz or 3 mins for...
Open the catalog to page 7
1 year Total Accuracy Specifications at TCal ±5°C & Range Parameters Range All specifications apply from 10% of full scale. AC Frequency Accuracy : 30ppm Settling Time: For 50% change in output: Less than 3 second from standby to within spec Inductive Loads : Up to 1H may be connected without additional protection providing the frequency/inductance combination does not exceed the maximum burden voltage. Due to continuous development specifications may be subject to change. 3010A Extended Specifications ACI Specifications : V1.81
Open the catalog to page 8
Stability (Accuracy relative to calibration Standards) Notes Note 1 : Temperature sensor on 30A range - microprocessor monitors & protects from overheating. Higher resistance loads allow a longer ON period. See graph for details. Note 2 : Specifications apply to loads of less than 10% of the maximum burden voltage. Due to continuous development specifications may be subject to change. 3010A Extended Specifications ACI Specifications : V1.81 www.Transmille.com
Open the catalog to page 9
Driving Coils and Inductive Loads When driving any load exceeding the maximum compliance voltage will cause the calibrator to trip into standby The maximum compliance voltage on the 10Amp range is specified at a max 2.8V RMS, 7.8V Peak to Peak at 220V supply Slightly higher compliances are available when powered from a 240V supply. When using EA002 with leads supplied it is possible to drive 30Amps/50Hz from a 230V supply, falling to 10Amps at 400Hz Specifications apply at TCal ± 5°C Outside this range an allowance of 0.18 x 1 Year Spec. per °C should be added. Time (Minutes) Current (Amps) Measurement...
Open the catalog to page 10
3010A EXTENDED SPECIFICATIONS Frequency Specifications TRANSMILLE LTD * Frequency band available from Firmware Version 12.3.16 / 13.0.06 Specifications apply at TCal ± 5°C Outside this range an allowance of 0.18 x 1 Year Spec. per °C should be added. Due to continuous development specifications may be subject to change. 3010A Extended Specifications Frequency Specifications : V1.81
Open the catalog to page 11
3010A EXTENDED SPECIFICATIONS DC Resistance Specifications TRANSMILLE LTD For the highest possible accuracy and dependability of the measured value, regardless of the measurement technique used, the 3000 Series calibrators use passive standard resistors, the calibrated value of which is displayed when selected. 1 year Total Accuracy Specifications at TCal ±5°C & Range Parameters For 2-Wire connection allow 35m on all resistance specifications. The 2 and 4 Wire value for each resistor is calibrated. The 2-Wire value is measured at the terminals The 4-Wire values are taken using the zero position...
Open the catalog to page 12All TRANSMILLE catalogs and technical brochures
8104 - Extended Specifications16 Pages
9000 Series Brochure9 Pages
4000 Series Operation Manual186 Pages
1000 SERIES14 Pages
Archived catalogs
3000A Series16 Pages
3200B10 Pages
- Management software solution
- Automation software solution
- Analysis software solution
- Process software
- TRANSMILLE Windows software
- IO module
- Cloud-based software
- Analog I/O
- Portable tester
- Industrial software
- Measurement software
- Interface software
- Automatic tester
- Generator
- Automated software
- Multimeter
- Voltage testing system
- Analog IO module
- Network software