C2110 series
1Pages

{{requestButtons}}

Catalog excerpts

C2110 series - 1

TRANSITION NETWORKS« The ION C2110 device provides an interface between 100Base-TX ports and 100Base-FX ports allowing users to integrate fiber optic cabling into 100Base-TX copper environments. Ordering Information C2110-1011 100Base-TX (RJ-45) [100 m/328 ft.] to 100Base-FX 1300nm multimode (ST) [2 km/1.2 mi.] Link Budget: 11.0 dB Features • Auto-Negotiation of speed and duplex on TP port • Auto-MDI/MDIX on TP port • Link Pass Through • Far-End-Fault (FEF) detection • Automatic Link Restoration • Pause advertisement • Field Upgradeable Firmware • Can be used in any ION Platform Chassis • Standards based, will link with any Standard 100Base-TX and any Standard 100Base-FX ports Manageable Features • Report converter status to chassis management software: - TP and Fiber Link Status - Hardware switch settings - Copper Port Speed - TP and Fiber Port Duplex - Fault condition • Write operation includes: - Power on/off device - Auto-Negotiation enable/disable - Force 10 Mbps or 100 Mbps - Force half or full-duplex - Select advertising modes when Auto-Negotiation is enabled - LPT enable/disable - FEF enable/disable - Pause enable/disable - Auto-MDI/MDIX enable/disable Note: Manageable Features are available when used in an ION Platform chassis along with an ION Management Module. www.transition.com Specifications Standards IEEE 802.3 Data Rate 100 Mbps, Layer 1 Switches SW1: Auto-Negotiation (UP = enabled) SW2: Pause (UP=enabled) SW3: Link Pass Through (UP = enabled) SW4: Far-End-Fault (FEF) (UP = enabled) Internal Jumpers Auto-MDI/MDIX: Enable/Disable Jumpers Hardware: Mode of operation is determined by the settings on the 4-position switch Software: Mode of operation is determined by the most recently saved on-board microprocessor settings Status LEDs PWR (Power): ON = Connection to powered backplane LKC (Copper Link): ON = Copper Link RXC (Receive Copper): Blinking = Data received on Copper link LKF (Fiber Link): ON = Fiber Link RXF (Receive Fiber): Blinking = Data received on Fiber Link Dimensions Width: 0.86” [22 mm] Depth: 6.5” [165 mm] Height: 3.4” [86 mm] Power Consumption 2.5 Watts, 200 mA @ 13.9 VDC Environment Environment specs are dependent on the chassis chosen Compliance CISPR/EN55022 Class A, FCC Class A, CE Mark Warranty Lifetime C2110-1019 100Base-TX (RJ-45) [100 m/328 ft.] to 100Base-FX 1310nm single mode (LC) [20 km/12.4 mi.] Link Budget: 17.3 dB C2110-1040 100Base-TX (RJ-45) [100 m/328 ft.] to 100Base-X SFP Slot (empty) Single Fiber Products Recommended use in pairs Transition Networks • Media Converters, Extenders, & NIDs Catalog | 11

Open the catalog to page 1

All Nom du compte Lantronix catalogs and technical brochures

  1. SM8TAT2DPB

    1 Pages

  2. SM24TAT2DPA

    1 Pages

  3. SM8TAT2SA

    1 Pages

  4. SM16TAT2SA

    1 Pages

  5. SM24TAT2SA

    1 Pages

  6. SGPAT Series

    1 Pages

  7. TN-EOT

    1 Pages

  8. IONDCR

    1 Pages

  9. C4110 Series

    1 Pages

  10. C3100 Series

    1 Pages

  11. F-SM-MM-05

    1 Pages

  12. E-TBT-FRL-05

    1 Pages