video corpo

CROSS CUT ADHESION TEST KIT CC3000
4Pages

{{requestButtons}}

Catalog excerpts

CROSS CUT ADHESION TEST KIT CC3000 - 1

Vision on quality www.tqc.eu TQC CROSS CUT ADHESION TEST - CC3000 SP1680, SP1681, SP1682, SP1683, SPI684I PRODUCT DESCRIPTION The TQC Cross Cut Adhesion Test KIT (CC3000) is used to test the adhesion of dry coats of paint on their substrate by means of a series of cuts through the coating. Two series of parallel cuts cross angled to each other to obtain a pattern of 25 or 100 similar squares. The ruled area is evaluated by using a table chart after a short treatment with a stiff brush, or adhesive tape for hard substrates. BUSINESS Protective coatings, Corrosion Control, Coating Laboratories, Paint Production, Surface Finishing, Powder Coatings, Decorative Coatings, Building Maintenance STANDARDS ISO 2409, ASTM D3359 FEATURES • The blade holder is kept at a set distance from the surface with the aid of two wheels (ball bearings). Reproducible test results guaranteed. • Ergonomically shaped handle • Easy to change cutting knife • Wide range of knife sizes available for different coating thicknesses and substrates and according to different standards. SCOPE OF SUPPLY • Soft grip handle • Hardened steel cutter (type may vary, see below schedule) • Nylon brush • Illuminated magnifier • Adhesive tape (adhesion to steel 4.3N/cm) and one 2 mm • Allen key 2908 LL Capelleaan den IJssel The Netherlands e-mail: info@tqc.eu www.tqc.eu

Open the catalog to page 1
CROSS CUT ADHESION TEST KIT CC3000 - 2

Vision on quality www.tqc.eu ORDERING INFORMATION Blades Teeth distance Coating thickness 0-60^m / on hard 0-2,4 mils substrates Coating thickness -on soft substrates Spare knifes ACCESSORIES SP3007 - Adhesion tape, single roll, adhesion to steel 4.3 N/cm SP3010 - Adhesion tape, set of 3 rolls, adhesion to steel 4.3 N/cm SP3020 - Adhesion tape, single roll, adhesion to steel 7.6 N/cm SP1710 - Nylon Brush for Cross Cut Adhesion Test SP9700 - Lighted Magnifier 2.5x SP1702 - Spare knife ISO + ASTM 1mm SP1703 - Spare knife ISO + ASTM 2mm SP1704 - Spare knife ISO 3mm SP1705 - Spare knife ASTM...

Open the catalog to page 2
CROSS CUT ADHESION TEST KIT CC3000 - 3

Vision on quality www.tqc.eu Classification SPECIAL CARE • Though robust in design, this instrument is precision-machined. Never drop it or knock it over • Always clean the instrument after use. • Clean the instrument using a soft dry cloth. Never clean the instrument by any mechanical means such as a wire brush or abrasive paper. This may cause, just like the use of aggressive cleaning agents, permanent damage. • Always keep the instrument in its case when not in use. SAFETY PRECAUTIONS • A knife is a sharp object. Be careful when using it. DISCLAIMER The right of technical modifications...

Open the catalog to page 3
CROSS CUT ADHESION TEST KIT CC3000 - 4

than death or personal injury resulting from our negligence) arising out of the use of the product. The information contained in this sheet is liable to modification from time to time in the light of experience and our policy of continuous product development. TQCB.V. 2908 LL Capelleaan den IJssel phone: +31 (0)10-7900100 e-mail: info@tqc.eu

Open the catalog to page 4

All TQC Sheen BV catalogs and technical brochures

  1. TM0030

    3 Pages

Archived catalogs

  1. COLORCATCH

    3 Pages