Test Equipment Depot - 800.517.8431 - TestEquipmentDepot.com Programmable Bidirectional DC-Power Supply © EA Elektro-Automatik in 2021, this information is subject to change without notice

EA-PSBE 10000 3U5 KW - 10 KW - 15 KWProgrammable Bidirectional DC-Power SupplyFeatures ■ Wide range input, 208 V - 480 V ±10 % 3ph AC ■ Active Power-Factor-Correction, typical 0.99 ■ Bidirectional power supply, 2-quadrants in source and sink ■ In load operation, regenerative with energy recovery into the grid ■ Very high efficiency up to over 96 % ■ High performance of up to 15 kW per unit ■ Flexible power regulated DC input/output stages (autoranging) ■ Regulation mode CV, CC, CP, CR with fast crossover ■ Digital regulation, high resolution with 16bit ADCs and DACs, selection of control speed:...

Technical data General specifications AC Input Voltage, Phases Power factor Leakage current Overvoltage category Pollution degree DC Output static Load regulation CV ≤0.05% FS (0 - 100% load, constant input voltage and constant temperature) ≤0.01% FS (208 V - 480 V AC +10% input voltage, constant load and constant temperature) ≤0.02% FS (Over 8hrs interval following 30 minutes warm-up, constant input voltage, load and temperature) ≤30ppm/°C (Following 30 minutes warm up) Compensation (Remote Sense) ≤0.1% FS (0 - 100% load, constant input voltage and constant temperature) ≤0.01% FS (208 V - 480...

Safety protection class Ingress Protection Operating temperature Storage temperature Humidity Altitude CSA C22.2 No 61010-1 BS EN 61010-1 EN 5501 1, class B CISPR 11, class B FCC 47 CFR Part 15B, Unintentional Radiator, class B EN 61326-1 include tests according to: Forced air flow from front to rear, temperature controlled fans 19“ x 3U x 668 mm (Enclosure only, not over all) 18.0 kg (40 lb) 5 kW unit 25.4 kg (56 lb) 10 kW unit 32.8 kg (72 lb) 15 kW unit this information is subject to change without notice

PSBE 10010-170 PSBE 10060-170 PSBE 10080-170 PSBE 10200-70 Technical specifications *1 100% Power and 100% Output voltage © EA Elektro-Automatik in 2021, this information is subject to change without notice

PSBE 10010-340 PSBE 10060-340 PSBE 10080-340 PSBE 10200-140 Technical specifications *1 100% Power and 100% Output voltage © EA Elektro-Automatik in 2021, this information is subject to change without notice

PSBE 10010-510 PSBE 10060-510 PSBE 10080-510 PSBE 10200-210 Technical specifications *1 100% Power and 100% Output voltage © EA Elektro-Automatik in 2021, this information is subject to change without notice

The bidirectional DC laboratory power supplies in the PSBE 10000 series from EA Elektro-Automatik are two quadrant devices which can perform the function of a power supply as well as that of an electronic load. In load mode the device is regenerative and feeds the energy back into the local grid with an efficiency up to over 96%. The PSBE 10000 series includes three phase units, which, together with the wide input range, allows use with practically all global mains voltages. The DC voltage and current are directed by the application and the spectrum ranges from 0 - 10 V to 0 - 2000 V and from...

The output of the bidirectional power supply PSBE 10000 with a DC voltage of 0 - 10 V up to 0 - 2000 V allows positive and negative currents of 0 - 20 A up to 0 - 1000 A as a two-quadrant device. The flexible output stages (autoranging) provide the user with a wide voltage, current and power range and hence a wider field of working than traditional power supplies. Connection of the DC output is via a copper rail on the back side of the device. If a system with higher performance is required, the devices are simply connected in parallel. With minimal effort devices can be linked with the vertical...

High performance systems High power applications can be covered with high power systems of up to 1920 kW. These are achieved by using the outputs of many PSBE 10000 devices, changing the copper rails to vertical, and connecting in parallel. Thus, a 19” cabinet with 42 U can provide a system with 240 kW occupying 0.6 m² floorspace. The master/slave bus enables up to 8 cabinets with a maximum of 64 units of 30 kW each to behave as one unit. If the integral master-slave bus and share bus are used, a multi device system behaves as a single device. The masterslave bus and the share bus are simply...

Application Battery test for electro mobility A typical application for the bidirectional power supplies from EA Elektro-Automatik is the testing of the electrical characteristics of a battery. The wide application spectrum covers cell, module or pack tests, the determination of the SOH (State-of-Health) for a second life classification as well as the End-of-Line (EOL) test. These applications put many demands on power electronics which are fulfilled by the PSB 10000 range. The excellent features of this device range are: measurement of voltage and current with the required accuracy and performance,...

Outline drawing PSBE 10000 3U <200 V © EA Elektro-Automatik in 2021, this information is subject to change without notice

Outline drawing PSBE 10000 3U >360 V © EA Elektro-Automatik in 2021, this information is subject to change without notice

2. TFT Control Interface, interactive operation and display 3. Rotary knob with push-button for settings and control 4. USB Host, use USB-stick for data logging and sequencing 5. Rotary knob with push-button for settings and control 6. On / Off push-button with LED status display 3. Share-Bus Interface to set up a system for parallel connection 4. Output voltage Remote Sense input terminal 5. Output terminal, Copper busbar 6. Mains input terminal 7. Grounding connection screw (PE) 8. Connector (DB15 Female) for isolated analog program, monitor and other functions 10. Master-Slave-Bus interface...

© EA Elektro-Automatik in 2021, this information is subject to change without notice Datasheet_PSBE_10000_3U_15kW_en_02