MODEL VERSION: SPEC VERSION : ISSUED DATE: □ Preliminary Specification Prelim ■ Final Product Specification TIANMA Confirmed : Prepared by Prepared This technical specification is subjected to change without notice The information contained herein is the exclusive property of TIANMA MICRO-ELECTRONICS Corporation and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of TIANMA MICRO-ELECTRONICS Corporation. Page 1 of 3

The information contained herein is the exclusive property of TIANMA MICRO-ELECTRONICS Corporation and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of TIANMA MICRO-ELECTRONICS Corporation. Page 2 of 31

Issued Date Preliminary Specification Release Modify the mistake of RA test requirements Final Product Release. change mechanical drawing，optical characteristics Update Packing Drawing and VCI MIN. value Modify SPI Interface Timing Characteristic (Page16 17)， update packing Add lifetime and update packing The information contained herein is the exclusive property of TIANMA MICRO-ELECTRONICS Corporation and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of TIANMA MICRO-ELECTRONICS Corporation. Page 3 of 3

1 General Specifications Feature Display Spec. Mechanical Characteristics Electrical Characteristics Size Resolution Technology Type Pixel Configuration Pixel pitch(mm) Display Mode Surface Treatment Viewing Direction Gray Scale Inversion Direction 3.5 inch 320(RGB) x 480 a-Si R.G.B. Vertical Stripe 0.153(H)x0.153(V) TM with Normally White HC 6 o'clock 12 o'clock LCM (W x H x D) (mm) Active Area(mm) With /Without TSP Matching Connection Type LED Numbers Weight (g) Interface Color Depth Driver IC 55.26 x 84.69 x 2.2 48.96x73.44 Without TSP ZIF 6 LEDs 21.0 MCU+ RGB+ SPI 65K/262K ILI9488 Note 1:...

Output a frame head pulse signal If no used, please open this pin Ground Data enable signal in RGB mode If no used, please fix this pin at GND level Pixel clock signal in RGB mode If no used, please connect this pin to GND Vertical sync. signal in RGB mode If no used, please connect this pin to GND Ground Horizontal sync, signal in RGB mode If no used, please connect this pin to GND MPU system interface mode select MPU system interface mode select MPU system interface mode select Analog POWER Serial data in/out pin in DBI Type C 9bit mode Serial data input pin in DBI Type B 8bit mode If no used,...

Read strobe signal If no used, please connect this pin to IOVCC (WR) Write data enable pin in DBI Type B (SCL) Write data enable pin in DBI Type C If no used, please connect this pin to IOVCC Data/command selection pin If no used, please connect this pin to IOVCC Chip select signal If no used, please connect this pin to IOVCC LED CATHODE P----Power/ Ground WR/SCL WR DBI TYPE-C Option 1(3 SCL wire) DBI TYPE-C Option 3(4 SCL wire) NC---Not Connected DATA Bus use Command/Parament GRAM DB7-DB0 DB17-DB0:18bits Data DB7-DB0 DB8-DB0:9bits Data DB7-DB0 DB15-DB0:16bits Data DB7-DB0 DB7-DB0:8bits Data...

3 Absolute Maximum Ratings Item Power Voltage Logic supply voltage Symbol VCI IOVCC RESET,CSX,SCL, Logic Input voltage SDA,D/CX Operating Temperature Top Storage Temperature Tst Relative Humidity Note2 Absolute Humidity Table 3.1 Absolute Maximum Ratings atings Note1: Input voltage include DB0~ DB17, Dotclk, Hsync, Vsync, Enable,RESET,CS,RD,WR/SCL,LCM_ID etc(For your reference) Note2: Ta means the ambient temperature. It is necessary to limit the relative humidity to the specified temperature range. Condensation on the module is not allowed. The information contained herein is the exclusive property...

4 Electrical Characteristics 4.1 LCD module Ta= 25℃ Item Logic Signal Input /Output Voltage Power Supply Voltage Input High Level Signal Voltage Low Level Output High Level Signal Voltage Low Level Black Mode Sleeping Mode (Panel+ LSI) Power Consumption Table 4.1 LCD module electrical characteristics Item Symbol Forward Current IF Forward Voltage VF Backlight Power Consumption W BL LED lifetime Remark 1 LED 1 LED 6 LEDs in parallel Note1: Figure below shows the connection of backlight LED. Note 2: 1LED: V F= 3.2V I F= 20mA C uD gm irc it ia ra e Note 3: : I Fis definedfor one LED. Optical performance...

C ontrol signal input interface TE G rayscale M anipulation Voltage The information contained herein is the exclusive property of TIANMA MICRO-ELECTRONICS Corporation and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of TIANMA MICRO-ELECTRONICS Corporation. Page 9 of 31

5 Timing Chart 5.1 DBI Type B 5.1.1 DBI Type B Timing Characteristic The information contained herein is the exclusive property of TIANMA MICRO-ELECTRONICS Corporation and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of TIANMA MICRO-ELECTRONICS Corporation. Page 10 of 31

The information contained herein is the exclusive property of TIANMA MICRO-ELECTRONICS Corporation and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of TIANMA MICRO-ELECTRONICS Corporation. Page 11 of 31

The information contained herein is the exclusive property of TIANMA MICRO-ELECTRONICS Corporation and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of TIANMA MICRO-ELECTRONICS Corporation. Page 12 of 31

The information contained herein is the exclusive property of TIANMA MICRO-ELECTRONICS Corporation and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of TIANMA MICRO-ELECTRONICS Corporation. Page 13 of 31

The information contained herein is the exclusive property of TIANMA MICRO-ELECTRONICS Corporation and shall not be distributed, reproduced, or disclosed in whole or in part without prior written permission of TIANMA MICRO-ELECTRONICS Corporation. Page 14 of 31