Catalog excerpts
HMT043ATA-7C LCD Module User Manual Release Date - Preliminary Draft release Document Name: HMT043ATA-7C-Manual-Rev0.1.doc Page: 1 of 12
Open the catalog to page 1LCD Module User Manual Document Name: HMT043ATA-7C-Manual-Rev0.1.doc Page: 2 of 12
Open the catalog to page 2LCD Module User Manual 1 Basic Specification TOPWAY HMT043ATA-7C is a Smart TFT Module with 32bit MCU on board. Its graphics engine provides numbers of outstanding features. It supports TOPWAY TML 3.0 for preload and pre-design display interface that simplify the host operation and development time. Suitable for industry control, instrumentation, medical electronics, power electric equipment applications. General Specification Screen Size(Diagonal) : Resolution : Color Depth : Pixel Configuration : Display Mode : Viewing Direction : Outline Dimension : Active Area : Backlight : Command I/F:...
Open the catalog to page 3LCD Module User Manual Terminal Function Descriptions Power supply No connection, leave open Data Input (eg. to PC’s RS232C pin3 <9pin D-connector>) Data output (eg. to PC’s RS232C pin2 <9pin D-connector>) Request To Send (could function as busy BUSY signal) (eg. to PC’s RS232C pin8 <9pin D-connector> ) Ground, (0V) 8, 9, 10 VSS P Note. *1. User data and commands transfer through this terminal. *2. HOST using command hand shake during communication is suggested. Power supply (5V) USB DATA negative signal USB DATA positive signal No connection, leave open Ground, (0V) Note. *1. TML files and...
Open the catalog to page 4LCD Module User Manual Items Operating Voltage Rx Input MARK(1) Rx Input SPACE(0) Tx Output MARK(1) Tx Output SPACE(0) RTS Output High RTS Output Low Operating Current Operating Current (USB) Battery Supply current Symbol VDD VRxM VRXS VTXM VTXS VTXH VTXL IDD IVUSB IBAT VSS=0V, TOP =25C Applicable Pin VDD Rx Rx Tx Tx RTS(BUSY) RTS(BUSY) VDD (*1) VUSB (*2) Note. *1. Normal display condition. *2. For Battery driving RTC application, RTC configuration should be enabled in the project global setting. And after install/re-install the battery, it should be power-on once for correct RTC...
Open the catalog to page 5LCD Module User Manual Quick Start Guide Install TOPWAY Graphics Editor Import pictures 2. design UI flow Connect to host Show 5. real time data Command Descriptions Please refer to “SMART LCD Command Manual” . Document Name: HMT043ATA-7C-Manual-Rev0.1.doc Page: 6 of 1
Open the catalog to page 6LCD Module User Manual 5 Optical Characteristics Item View Angles Contrast Ratio Response Time TOFF White Blue Uniformity NTSC Luminance 1.IF= 40 mA, and the ambient temperature is 25℃. 2. The test systems refer to Note 1 and Note 2.
Open the catalog to page 7LCD Module User Manual Note 1: The data are measured after LEDs are turned on for 5 minutes. LCM displays full white. The brightness is the average value of 9 measured spots. Measurement equipment SR-3A (1°) Measuring condition: - Measuring surroundings: Dark room - Measuring temperature: Ta=25℃. - Adjust operating voltage to get optimum contrast at the center of the display. Note 3: The definition of contrast ratio (Test LCM using SR-3A (1°)): Luminance When LCD is at “White” state Contrast = Ratio(CR) Luminance When LCD is at “Black” state (Contrast Ratio is measured in optimum common...
Open the catalog to page 8LCD Module User Manual 6 LCD Module Design and Handling Precautions Please ensure V0, VCOM is adjustable, to enable LCD module get the best contrast ratio under different temperatures, view angles and positions. Normally display quality should be judged under the best contrast ratio within viewable area. Unexpected display pattern may com out under abnormal contrast ratio. Never operate the LCD module exceed the absolute maximum ratings. Never apply signal to the LCD module without power supply. Keep signal line as short as possible to reduce external noise interference. IC chip (e.g. TAB...
Open the catalog to page 9LCD Module User Manual the electric circuit of LCD module. Only clean LCD with a soft dry cloth, Isopropyl Alcohol or Ethyl Alcohol. Other solvents (e.g. water) may damage the LCD. Never add force to components of LCD module. It may cause invisible damage or degrade the module's reliability. When mounting LCD module, please make sure it is free from twisting, warping and bending. Do not add excessive force on surface of LCD, which may cause the display color change abnormally. LCD panel is made with glass. Any mechanical shock (e.g. dropping from high place) will damage the LCD module....
Open the catalog to page 10LCD Module User Manual 7.2 Surface Mounting (Figure 2) As the CTP assembling on the countersink area with double side adhesive. The countersink area should be flat and clean to ensure the double side adhesive installation result. - The Bezel is recommend to keep a gap (≥0.3mm each side) around the cover lens for tolerance. - It is recommended to provide an additional support bracket with gasket for backside support when necessary (e.g. TFT module without mounding structure). They should only provide appropriate support and keep the module in place. - The mounting structure should be strong...
Open the catalog to page 11LCD Module User Manual ITO film be damaged and shorten its lifetime. It is suggested to protect those areas with gasket (between the bezel and RTP).The suggested figures are B≥0.50mm; C≥0.50mm. (Figure 4) The bezel side wall should keep space E= 0.2 ~ 0.3mm from the RTP. (Figure 4) 垫缓冲物(Gasket),我们建议设计面框应覆盖动作区 的边缘,面框边缘到 V.A.区的距离 B≥0.50mm; 垫圈内 边缘到 V.A.区的距离 C≥0.50mm. (附图 4) 在设计面框与 RTP 组装时,应考虑到面框内侧与 RTP 外 侧的间距 E≥0.2mm. (附图 4) 通常设计时: RTP 的可视区 V.A. 应不小于 TFT 的可视区 V.A. 及 RTP 的动作区 A.A. 应不小于 TFT 的动作区 A.A. (附图 5) In general design, RTP V.A. should be bigger than the TFT V.A. and RTP A.A. should be...
Open the catalog to page 12SMART LCD Command V5.04 Manual Release Date - Preliminary Draft release - Add a description of the 0xE8 command - 4.1, 0xE2, 0xE3 command name correction - Add a description of the 0xE7 command www.topwaydisplay.com www.topwaysz.com Document Name:SMART LCD Command v5.04 Manual Rev0.4.doc Page: 1 of 19
Open the catalog to page 13SMART LCD Command Manual
Open the catalog to page 14SMART LCD Command Manual 1 Basic Specifications TOPWAY Smart LCD serial command is for real-time control and access. Host machine get the data which input through the Smart LCD interface or provide the data for display. Hardware connection Smart LCD serial UART interface are mainly base on RS232-C standard, by default, config as 8N1 115200bps. Communication Packet Structure Commands and Response Packet should be format as follow (hostmodule): Seq 1 2 Code type Packet header Command code Parameter or Data Packet tail Note. *1. Unless otherwise specified, all the multi-byte values, data,...
Open the catalog to page 15All TOPWAY LCD catalogs and technical brochures
-
10.1" TFT LCD Module
1 Pages
-
MONO Product
2 Pages
-
LMT050DNCFWU-NNA-2
15 Pages
-
LMT080TDGP01
16 Pages
-
HKT035BTB-1D
36 Pages
-
HMT050AMC-C
17 Pages
-
HMT043ATA-6C
31 Pages
-
TM035PDHG09
42 Pages
-
TM035PDHG03
31 Pages
-
TM028HDZP01
28 Pages
-
LM256160DCW-1
14 Pages
-
LM12896FCW-1
17 Pages
-
LM12832KCW
13 Pages
-
LM2088EFW-9
12 Pages
-
LM3122AGG-2
12 Pages
-
LM240160YCW
18 Pages
-
LM6093ACW
14 Pages
-
HMT104ATA-C
11 Pages
-
HMT101ATA-D
36 Pages
-
HKT080ATA-C
1 Pages
-
HMT080ATA
1 Pages
-
HKT070DTA-1C
11 Pages
-
HMT070DTA-D
1 Pages
-
HKT070DMC-2C
19 Pages
-
HMT070ETD-C
31 Pages
-
HMT070ETD-1D
34 Pages
-
HMT056ATA-C
1 Pages
-
HMT050CB-1C
31 Pages
-
HMT050DTA-D
1 Pages
-
HKT050ATA-C
1 Pages
-
HMT043GTA-1D
37 Pages
-
HKT043BMC-2C
17 Pages
-
HMT043ATA-3C
11 Pages
-
HMT043BMC-C
1 Pages
-
HMT043ATA-4C
11 Pages
-
HKT043BMC-C
1 Pages
-
HKT043ATA-1C
12 Pages
-
HMT035ATA-D
13 Pages
-
HMT028ATB-C
12 Pages
-
HKT104ATA-C
31 Pages
-
HMT068BTA-C
33 Pages
-
HMT070ATA-1C
32 Pages
-
HMT080ATA-C
33 Pages
-
HMT090ATA-C
30 Pages
-
HMT101ATA-C
33 Pages
-
HMT050ATA-2C
31 Pages
-
HMT043ATA-2C
32 Pages
-
IC Raio RA6963 LCD Controller
42 Pages
-
IC Epson S1D13L01 LCD Controller
118 Pages
-
IC EPSON S1D13700 LCD Controller
133 Pages
-
EPSON S1D13709 LCD Controller
192 Pages
-
Samsung S6B0108 LCD Driver
23 Pages
-
Avant SBN0064G LCD Driver
37 Pages
-
Avant SBN6400G LCD Driver
34 Pages
-
EPSON SED1335 LCD Controller
95 Pages
-
SGS-THOMSON ST7282
23 Pages
-
Raio RA6963 LCD Controller
42 Pages
-
Raio RA8875 TFT LCD Controller
174 Pages
-
Raio RA8835 LCD Controller
93 Pages
-
RAIO RA8803 LCD Controller
8 Pages
-
HMT035ATA-1C
1 Pages
-
Smart LCD introduction
14 Pages
-
Topway company introduction
14 Pages
-
TFT module in bezel
1 Pages
-
Topway TFT LCD
1 Pages
-
LM12864L Series
1 Pages
-
LM12864T Series
1 Pages
-
LM12864F Series
1 Pages
-
LM6060C Series
1 Pages
-
LM12864M Series
1 Pages
-
LM6029A Series
1 Pages
-
LM6059B Series
1 Pages
-
LM24048A Series
1 Pages
-
LM13232A Series
1 Pages
-
LM160160A Series
1 Pages
-
LMB402C Series
1 Pages
-
LMB242A Series
1 Pages
-
LMB204C Series
1 Pages
-
LM3121 Series
1 Pages
-
LMB404A Series
1 Pages
-
HMT043FC-1C
1 Pages
-
LM3123 Series
1 Pages
-
LMB204B Series
1 Pages
-
LMB202E Series
1 Pages
-
LMB202D Series
1 Pages
-
LMB164A Series
1 Pages
-
LMB162G Series
1 Pages
-
LMB162H Series
1 Pages
-
LMB162N Series
1 Pages
-
LMB162A Series
1 Pages
-
LMB0820D Series
1 Pages
-
LMB0820C Series
1 Pages
-
LMB0820A Series
1 Pages
-
LMB081N Series
1 Pages
-
LMB081A Series
1 Pages
-
LMB162X series
1 Pages
-
LMT057DNAFWU-AAN series
1 Pages
-
LMT057DNAFWU-AAA series
1 Pages
-
LMT104SDH01 Series
1 Pages
-
TOPWAY Product List (Y2012)
4 Pages
-
TFT LCD module
1 Pages
-
Without controller
1 Pages
-
Chinese fonts
1 Pages
-
Built-in controller
1 Pages
-
Character module
1 Pages