Catalog excerpts
FEATURES •Ultrasonic technology •No moving parts •4 flow ranges Accuracy ±1% of reading 2 - 100% range ±2% of reading 0 - 2% of range •Repeatability ±0.1% +0.005% FSD •Pulse output, NPN and PNP •20 Bar rating •8 - 24 Vdc operation •Large turndown ratio •p” BSP fittings •IP65 enclosure •65°C operation. •Pre-set ‘K’ factors The Atrato Process is based on our standard, wide ranging, Atrato meter but packaged to address the more challenging process and control environment. The body is 316 stainless steel, rated at 20 Bar and the electronics are built-in and sealed to IP65. The only other wetted materials are PEEK and the customer’s choice of elastomers. They are calibrated with a pre-set ‘K’ factor so all meters of the same flow range are fully interchangeable simplifying assembly and set-up procedures for OEM manufacturers. There are two adaptable frequency outputs, one PNP and NPN. Two multicolour LEDs indicate signal strength, power malfunctions and pulse outputs. Electrical connections are through a standard M12, four pin, sensor connector. Four flow ranges are available from 2 ml/min to 15 litres per minute, accuracy is ±1% over the whole flow range. Flow Range 2 to 500ml/min 0.01 to1.5 L/min 0.03 to 5 L/min 0.1 to 15 L/min ‘K’ factor Pulses per litre 100000 20000&nb
Open the catalog to page 1First 3 digits Forth digit Fifth digit Sixth digit Seventh digit Standard flow range seal material process fittings thread type Tube assembly materials V = Viton® N = Nitrile E = EPDM S = Silicon K = Kalrez® For example 76P - VQB - O This is a 15 L/Min flowmeter with Viton seals, quarter inch BSP fittings and a 316 stainless steel flow tube with PEEK internal fittings. Process Atrato Linearity - Green line ±1.0% of reading from 2 to 100% of range - Black line ±2.0% of reading minimum flow to 2% of range Repeatability - Red line ±0.1% of reading plus 0.005% of full scale 3 TITAN ENTERPRISES...
Open the catalog to page 2All Titan Enterprises catalogs and technical brochures
-
Analogue Converter
2 Pages
-
Turbine Flowmeters Overview
2 Pages
-
Metra-Clear Oval Gear Meter
2 Pages
-
OG7 500L/Min Oval Gear Meter
2 Pages
-
OG6 200L/Min Oval Gear Meter
2 Pages
-
OG5 100L/Min Oval Gear Meter
2 Pages
-
OG4 50L/Min Oval Gear Meter
2 Pages
-
OG3 10L/Min Oval Gear Meter
2 Pages
-
OG2 4L/Min Totaliser
2 Pages
-
OG1 1L/Min Oval Gear Meter
2 Pages
-
Oval Gear Meters Overview
2 Pages
-
Beverage Meter
1 Pages
-
Flow Rate Totaliser
1 Pages
-
FT2 Hall Effect Detection
2 Pages
-
FT2 Optical Detection
2 Pages
-
1000 Series Flowmeter
2 Pages
-
Atrato 8pp
8 Pages
-
Atrato
8 Pages
-
1000 Series Flowmeter
2 Pages
-
Insertion Turbine
2 Pages
-
800 Series Flowmeter
2 Pages
-
OG5 Oval Gear Meter
2 Pages
-
Beverage Meter
1 Pages
-
Metra-Clear
2 Pages
-
OG2 Totaliser
2 Pages
-
Analogue Converter
2 Pages
-
OG1 Oval Gear Meter
2 Pages
-
OG2 Oval Gear Meter
2 Pages
-
OG3 Oval Gear Meter
2 Pages
-
OG4 Oval Gear Meter
2 Pages
-
OG6 Oval Gear Meter
2 Pages
-
OG7 Oval Gear Meter
2 Pages
-
900 Series Flowmeter
2 Pages