Catalogs >
TiMOTION Europe >
VN3 series

VN3 series
6Pages

Catalog excerpts

series Product Segments • Industrial Motion The VN3 series linear actuator is specifically designed for ventilation applications to help quickly remove smoke, heat, and toxic gases from buildings in the event of a fire. It is also engineered to support a reduced smoke layer in the lower parts of a room. The VN3 is constructed with high-quality aluminum, making it ideal for applications like fall-through protection systems and greenhouses. The VN3 has a higher load capacity than the VN2, and is currently equipped with either a 12V or 24V DC motor. General Features Max. load Max. speed at max. load Max. speed at no load Retracted length IP rating Stroke Output signals Options Voltage Operational temperature range Operational temperature range at full performance 3,000N (push/pull) 3.5mm/s 6.8mm/s > Stroke + 248mm IP66 20~500mm Hall sensors Safety nut 12/24V DC; 12/24V DC (thermal switch) -20°C~+65°C +5°C~+45°C

Open the catalog to page 1

Drawing Standard Dimensions (mm) Load and Speed CODE Load (N) Push Pull Self Locking Force (N) Typical Current (A) No Load With Load Typical Speed (mm/s) No Load With Load Motor Speed (5600RPM, Duty Cycle 10%) B 3000 3000 3000 <0.4 <3.2 6.8 3.5 Note 1 Please refer to the approved drawing for the final authentic value. 2 This self-locking force level is reached only when a short circuit is applied on the terminals of the motor. All the TiMOTION control boxes have this feature built-in. 3 The current & speed in table are tested with 24V DC motor. With a 12V DC motor, the current is...

Open the catalog to page 2

Motor Speed (5600RPM, Duty Cycle 10%) Speed vs. Load 8.0 7.0 6.0 Performance Data (24V DC Motor)

Open the catalog to page 3

Rear Attachment (mm) See page 6 1 = luminum, U clevis, slot 6.2, depth 13, hole 6.2 A 2 = luminum, U clevis, slot 6.2, depth 13, hole 8.2 A 3 = 12V DC, thermal switch 4 = 24V DC, thermal switch 3 = luminum, U clevis, slot 6.2, depth 13, hole10.2 A Outer Tube 0 = Without (Option when choosing rear attachment #1, #2, #3) Adjustable Clamping Block Mounting Bracket 0 = Without (Option when choosing rear attachment #1, #2, #3) Front Attachment (mm) See page 6 1 = luminum, U clevis, slot 6.2, depth 17, hole 6.2 A 2 = luminum, U clevis, slot 6.2, depth 17, hole 8.2 A Direction of Rear Attachment...

Open the catalog to page 4

VN3 Ordering Key Appendix Retracted Length (mm) 1. Calculate A+B = Y 2. Retracted length needs to > Stroke+Y

Open the catalog to page 5

VN3 Ordering Key Appendix Rear Attachment (mm) 1 = Aluminum, U clevis, slot 6.2, 2 = Aluminum, U clevis, slot 6.2, 3 = Aluminum, U clevis, slot 6.2, Front Attachment (mm) 1 = Aluminum, U clevis, slot 6.2, 2 = Aluminum, U clevis, slot 6.2, 3 = Aluminum, U clevis, slot 6.2, Wiring Definition Signal Output Pin / Color Green Red O White Black Yellow flBlue 0 Without Extend+ - - - Retract+ - 2 Hall sensor Extend+ VCC Hall 1 Com Retract+ Hall 2 Connector 1 = DIN 6P, 90° plug 2 = Tinned leads Terms of Use The user is responsible for determining the suitability of TiMOTION products for a specific...

Open the catalog to page 6