Product Segments • Industrial Motion The VN2 series linear actuator is designed specifically for ventilation applications to help remove smoke, heat, and toxic gases from buildings quickly in the event of a fire. It is also designed to generate a minimum smoke layer in the lower parts of a room. The VN2 is made of high-quality aluminum, suitable for applications like fall-through protection systems and greenhouses. The VN2 is currently equipped with either a 12V or 24V DC motor. General Features Max. load Retracted length Output signals Operational temperature range Operational temperature range

Drawing Standard Dimensions (mm) Load and Speed (12V DC) CODE Load (N) Push Pull Self Locking Force (N) No Load With Load No Load With Load Load and Speed (24V DC) CODE Load (N) Push Pull Self Locking Force (N) No Load With Load No Load With Load Note 1 Please refer to the approved drawing for the final authentic value. 2 The current & speed in table are tested with 24V DC motor. With a 12V DC motor, the current is approximately twice the current measured in 24V DC; speed will be similar for both voltages. 4 The current & speed in table are tested when the actuator is extending under push load....

Motor Speed (5200RPM, Duty Cycle 20%:2min on/8min off) Speed vs. Load 12.0 Performance Data (12V DC Motor)

Motor Speed (5200RPM, Duty Cycle 20%:2min on/8min off) Speed vs. Load 12.0 Performance Data (24V DC Motor)

Rear Attachment (mm) See page 7 1 = Plastic, slotless, hole 6.2 2 = Plastic, slotless, hole 8.2 3 = 12V DC, thermal switch 4 = 24V DC, thermal switch 3 = Plastic, U clevis, slot 6.2, depth 12.5, hole 6.2 4 = Plastic, U clevis, slot 6.2, depth 12.5, hole 8.2 Outer Tube Adjustble 0 = Without (Option when choosing rear attachment #1, #2, #3, #4) Clamp Block Mounting Bracket 0 = Without (Option when choosing rear attachment #1, #2, #3, #4) Front Attachment (mm) See page 7 1 = Aluminum, slotless, hole 6.2 2 = Aluminum, slotless, hole 8.2 3 = Plastic, U clevis, slot 6.2, depth 12.5, hole 6.2 Direction...

2. Retracted length needs to > Stroke+Y * Tolerance: fully extended length & retracted length ±3mm

VN2 Ordering Key Appendix Rear Attachment (mm) 1 = Plastic, slotless, hole 6.2 2 = Plastic, slotless, hole 8.2 3 = Plastic, U clevis, slot 6.2, depth 12.5, hole 6.2 4 = Plastic, U clevis, slot 6.2, depth 12.5, hole 8.2 Front Attachment (mm) 1 = Aluminum, slotless, hole 6.2 2 = Aluminum, slotless, hole 8.2 3 = Plastic, U clevis, slot 6.2, depth 12.5, hole 6.2 4 = Plastic, U clevis, slot 6.2, depth 12.5, hole 8.2 5 = Plastic, U clevis, slot 6.2, depth 22.5, hole 8.2 ø8.2

VN2 Ordering Key Appendix Connector 1 = DIN 6P, 90° plug 2 = Tinned leads C = Y cable (direct cut, water proof, anti-pull) Cable Length for Direct Cut System (mm)

qo t moTion Wire Definition Port Functions of Limit Wire Color AWG Two limit switches cut off the actuator at end of stroke Two limit switches send signal at end of stroke Output Signal EXT+ EXT+ RET+ RET+ EXT+ EXT+ RET+ RET+ Terms of Use The user is responsible for determining the suitability of TiMOTION products for a specific application. TiMOTION products are subject to change without prior notice.