Product Segments • Industrial Motion The VN1 series linear actuator was specifically designed for ventilation applications to help remove smoke, heat, and toxic gases from the building quickly in the event of a fire. It was also designed to create a minimum smoke layer in the lower parts of the room. The VN1 is made of high-quality aluminum, suitable for applications like fall-through protection systems and greenhouses.The VN1 is equipped with either a 12V or 24V DC motor. The AC version of the VN1 is equipped with a built-in SMPS which allows the supply of alternating current. General Features Max. load Retracted length depending on chosen options); ≥ 401mm (AC version; depending on chosen options) Stroke 20~500mm Output Signals Hall sensors Operational temperature range Operational temperature range

Dimensions with DC Voltage Retracted Length Dimensions with AC Voltage Retracted Length

Load and Speed - DC Motor CODE Self Locking Force (N) Motor Speed (5200RPM, Duty Cycle 30%) B Motor Speed (5200RPM, Duty Cycle 10%) D Note 1  Please refer to the approved drawing for the final authentic value. 2  This self-locking force level is reached only when a short circuit is applied on the terminals of the motor. All the TiMOTION control boxes have this feature built-in. 3  The current & speed in table are tested with 24V DC motor. With a 12V DC motor, the current is approximately twice the current measured in 24V DC; speed will be similar for both voltages. If choosing the voltage option...

Load and Speed - AC Motor Load (N) Push Self Locking Force (N) With Load With Load Motor Speed (5200RPM, Duty Cycle 30%) B Motor Speed (5200RPM, Duty Cycle 10%) D Note 1  Please refer to the approved drawing for the final authentic value. The load speed is tested during 50Hz condition. 2  This self-locking force level is reached only when a short circuit is applied on the terminals of the motor. All the TiMOTION control boxes have this feature built-in. 3  The current & speed in table are tested when the actuator is extending under push load. 4  Standard stroke: Min. ≥ 20mm, Max. please refer...

Motor Speed (5200RPM, Duty Cycle 30%) Speed vs. Load 12.0 Performance Data (24V DC Motor)

Motor Speed (5200RPM, Duty Cycle 10%) Speed vs. Load 15.0 Performance Data (24V DC Motor)

Motor Speed (5200RPM, Duty Cycle 30%) Speed vs. Load 12.0 Performance Data (220V AC Motor)

Motor Speed (5200RPM, Duty Cycle 10%) Speed vs. Load 12.0 Performance Data (220V AC Motor)

0 = Without (choose outer tube adjustable attachment) Outer Tube Adjustble Attachment (Clamping Block) See page 11 0 = Without 1 = Hole M8 (without rear attachment) Trunnion Mount Bracket Front Attachment (mm) See page 12 B = Rod end bearing, hole 8.0 C = Rod end bearing, hole 10.0 1 = Aluminum casting, no slot, hole 6.4 2 = Aluminum casting, no slot, hole 8.0 3 = Aluminum casting, no slot, hole 10.0 7 = luminum CNC, U clevis, slot 6.2, depth 16.0, hole 6.4 A 8 = luminum CNC, U clevis, slot 6.2, depth 16.0, hole 8.0 A 9 = luminum CNC, U clevis, slot 6.2, depth 16.0, hole 10.0 A Direction of Rear...

Set Upper Stroke Limitation by Software Full stroke, Standard defult value Set Lower Stroke Limitation by Software 0000, standard defult value Extension Soft Stop Length 0 = No deceleration, standard defult value Retraction Soft Stop Length 0 = No deceleration, standard defult value 2 = Sync, 2 actuators in system C Over Current Protection P = ut current for over current protection, extend and retract over current protection value are standard defult value Note: please contact TiMOTION before making an order Extend Speed 0 = PWM output 100%, standard defult value 9 = PWM output 90% 8 = PWM output...

VN1 Ordering Key Appendix Retracted Length (mm) 1. Calculate A+B = Y The total Retacted length calculated must be equal or longer 2. Retracted length needs to ≥ Stroke+Y than below minimum value. 1. When Choosing the Outer Adjustable Attachment Front Attach. Outer Tube Outer Tube Adjustble Attachment (Clamp Block) 1 = ole M8 (without rear H attachment) 2 = ole ø8 (without rear attachment) H

VN1 Ordering Key Appendix Front Attachment (mm) B = Rod end bearing, hole 8.0 ø8 1 = luminum casting, no slot, hole A 6.4 2 = luminum casting, no slot, hole A 8.0 7 = luminum CNC, U clevis, slot 6.2, A depth 16.0, hole 6.4 9 = luminum CNC, U clevis, slot 6.2, A depth 16.0, hole 10.0 8 = luminum CNC, U clevis, slot 6.2, A depth 16.0, hole 8.0 3 = luminum casting, no slot, hole A 10.0 Direction of Rear Attachment (Counterclockwise) 0 = ithout (When rear attachment W is outer tube slide clamp block) Terms of Use The user is responsible for determining the suitability of TiMOTION products for a specific...