Product Segments • Comfort Motion • Ergo Motion TiMOTION's TA9 is one of the smart furniture actuator options with compact dimension. This linear actuator is designed with a custom gear box, molded with a specially formulated plastic material which allows the TA9 to support load ratings up to 2500N. An EMC certification has been attained for this series, which is also available with optional IP54 or IP66 protection. General Features Max. speed at max. load Max. speed at no load Retracted length IP rating Certificate Output signals Operational temperature range

Standard Dimensions Retracted Length

Push Pull Self Locking Force (N) Typical Current (A) No Load With Load No Load With Load Motor Speed (4100RPM, Duty Cycle 10%) Motor Speed (3800RPM, Duty Cycle 10%) Motor Speed (3400RPM, Duty Cycle 10%) Motor Speed (2200RPM, Duty Cycle 10%) 1 Please refer to the approved drawing for the final authentic value. 2 This self-locking force level is reached only when a short circuit is applied on the terminals of the motor. All the TiMOTION control boxes have this feature built-in. 3 The current & speed in table are tested with 24V DC motor. With a 12V DC motor, the current is approximately twice the...

Motor Speed (4100RPM, Duty Cycle 10%) Speed vs. Thrust 70.0 Performance Data (24V DC Motor)

Motor Speed (3800RPM, Duty Cycle 10%) Speed vs. Thrust 70.0 Performance Data (24V DC Motor)

Performance Data (24V DC Motor) Motor Speed (3400RPM, Duty Cycle 10%)

Motor Speed (2200RPM, Duty Cycle 10%) Speed vs. Thrust 60.0 Performance Data (24V DC Motor)

Retracted Length (mm) See page 9 Rear Attachment (mm) See page 10 1 = Plastic, U clevis, slot 5.2, depth 13.0, hole 8.0, with plastic T-busing 1 = Aluminum casting, no slot, hole 8.0 3 = Aluminum casting, U clevis, width 6.0, depth 13.0, hole 8.0 4 = Aluminum casting, U clevis, width 6.0, depth 13.0, hole 10.0 Special Functions for Spindle SubAssembly 0 = Without 2 = Standard push only Output Signal 1 = Two switches at full retracted / extended positions to cut current 2 = Two switches at full retracted / extended positions to cut current + 3rd LS to send signal 3 = Two switches at full retracted...

TA9 Ordering Key Appendix Retracted Length (mm) 2. Retracted length needs to > Stroke+Y

TA9 Ordering Key Appendix Rear Attachment (mm) 1 = Plastic, U clevis, slot 5.2, depth 13.0, hole 8.0, with plastic T-busing 9 Front Attachment (mm) 3 = Aluminum casting, U clevis, width 6.0, depth 13.0, hole 8.0 4 = Aluminum casting, U clevis, width 6.0, depth 13.0, hole 10.0 1 = Aluminum casting, no slot, hole 8.0 Direction of Rear Attachment 1 = 0°

TA9 Ordering Key Appendix Functions for Limit Switches Wire Definitions CODE Pin • 1 (Green) 2 (Red) O 3 (White) 4 (Black) 5 (Yellow) A (Blue) 1 extend (VDC+) N/A N/A N/A retract (VDC+) N/A 2 extend (VDC+) N/A middle switch pin B middle switch pin A retract (VDC+) N/A 3 extend (VDC+) common upper limit switch N/A retract (VDC+) lower limit switch 4 extend (VDC+) common upper limit switch medium limit switch retract (VDC+) lower limit switch C = Y cable (For direct cut system, water proof, anti pull) Cable length for direct cut system (mm) P = Molex 8P, 90° plug, without anti-clip The user is...