TA50
8Pages

Catalog excerpts

Product Segments • Care Motion The TA50 is an innovative addition to TiMOTION’s CARE line of electric linear actuators. Featuring a cylindrical design, it incorporates an internal limit switch assembly installed inside the gearbox. Additionally, offering a robust load capacity of up to 8,000N and a waterproof rating of IP66, the TA50 is suitable for a wide variety of medical products, including electric hospital beds, bathroom chairs, and homecare medical beds. General Features Max. load Retracted length Output signals Hall sensors Operational temperature range

Open the catalog to page 1

Retracted Length Load and Speed CODE Self Locking Force (N) Motor Speed (4500RPM, Duty Cycle 10%) C Motor Speed (3800RPM, Duty Cycle 10%) H Note 1 Please refer to the approved drawing for the final authentic value. 2 This self-locking force level is reached only when a short circuit is applied on the terminals of the motor. All the TiMOTION control boxes have this feature built-in. 3 T he current & speed in table are tested with 24V DC motor. With a 12V DC motor, the current is approximately twice the current measured in 24V DC; speed will be similar for both voltages. 4 The current & speed...

Open the catalog to page 2

Motor Speed (4500RPM) Speed vs. Load 25.0 Performance Data (24V DC Motor)

Open the catalog to page 3

Motor Speed (3800RPM) Speed vs. Load 25.0 Performance Data (24V DC Motor)

Open the catalog to page 4

Rear Attachment (mm) See page 7 2 = Plastic, U clevis, width 8.2, depth 17.0, hole 10.2 (for push < 4000N) 3 = Plastic, U clevis, width 8.2, depth 17.0, hole 12.2 (for push < 4000N) 4 = Aluminum casting, U clevis, width 8.2, depth 17.0, hole 10.2 5 = Aluminum casting, U clevis, width 8.2, depth 17.0, hole 12.2 Front Attachment (mm) See page 7 1 = Punched hole on inner Aluminum tube + plastic cap, without slot, hole 10.2, plastic bush 2 = Punched hole on inner Aluminum tube + plastic cap, without slot, hole 12.2 3 = Plastic, U clevis, width 8.2, depth 20.0, hole 10.2 (for push < 4000N, pull...

Open the catalog to page 5

TA50 Ordering Key Appendix Retracted Length (mm) 1. Calculate A+B+C = Y 2. Retracted length needs to ≥ Stroke+Y A. Front Attach. Rear Attach. Front Attach. * For stroke over 300mm, please contact our engineers

Open the catalog to page 6

TA50 Ordering Key Appendix Rear Attachment (mm) 2 = Plastic, U clevis, width 8.2, depth 17.0, hole 10.2 (for push < 4000N) 3 = Plastic, U clevis, width 8.2, depth 17.0, hole 12.2 (for push < 4000N) 5 = Aluminum casting, U clevis, width 8.2, depth 17.0, hole 12.2 4 = Aluminum casting, U clevis, width 8.2, depth 17.0, hole 10.2 4 = Plastic, U clevis, width 8.2, depth 20.0, hole 12.2 (for push < 4000N, pull < 2500N) 8 = Aluminum casting, U clevis, width 6.2, depth 17.0, hole 12.2 7 = Aluminum casting, U clevis, width 6.2, depth 17.0, hole 10.2 6 = Punched hole on inner Aluminum tube, wihout...

Open the catalog to page 7

TA50 Ordering Key Appendix Direction of Rear Attachment (Counterclockwise) 1 = 0° Functions for Limit Switches Wire Definitions CODE extend (VDC+) 5 (Yellow) retract (VDC+) Q = Molex 6P, 90°plug, without anti-clip Terms of Use The user is responsible for determining the suitability of TiMOTION products for a specific application. TiMOTION products are subject to change without prior notice

Open the catalog to page 8