Product Segments • Comfort Motion • Industrial Motion TiMOTION’s TA4 series linear actuator is compact, quiet and powerful. It is designed to fit in an area specifically requiring a right angle motor and can be equipped with a Hall sensor for feedback. Certifications for the TA4 linear actuator include IEC60601-1, ES60601-1, UL73 and EMC. In addition, the TA4 is available with an optional IP54 or 66 rating. General Features Max. load Retracted length Hall sensors Operational temperature range

Standard Motor Dimensions Retracted Length Short Motor Dimensions Retracted Length

Load and Speed CODE Self Locking Force (N) Motor Speed (4100RPM, Duty Cycle 10%) A Motor Speed (3800RPM, Duty Cycle 10%) G Motor Speed (3400RPM, Duty Cycle 10%) M Motor Speed (2200RPM, Duty Cycle 10%) R Note 1  Please refer to the approved drawing for the final authentic value. 2  This self-locking force level is reached only when a short circuit is applied on the terminals of the motor. All the TiMOTION control boxes have this feature built-in. 3  The current & speed in table are tested with 24V DC motor. With a 12V DC motor, the current is approximately twice the current measured in 24V DC;...

Motor Speed (4100RPM) Speed vs. Load 40.0 35.0 30.0 Performance Data (24V DC Motor)

Motor Speed (3800RPM) Speed vs. Load 30.0 Performance Data (24V DC Motor)

Motor Speed (3400RPM) Speed vs. Load 25.0 Performance Data (24V DC Motor)

Motor Speed (2200RPM) Speed vs. Load 25.0 Performance Data (24V DC Motor)

Rear Attachment (mm) See page 10 1 = Aluminum casting, U clevis, slot 6.0, width 11.0, hole 6.4 2 = Aluminum casting, U clevis, slot 6.0, width 11.0, hole 8.0 3 = Aluminum casting, U clevis, slot 6.0, width 11.0, hole 10.0 Front Attachment (mm) See page 10 1 = Aluminum casting, hole 6.4 2 = Aluminum casting, hole 8.0 3 = Aluminum CNC, U clevis, slot 6.0, depth 16.0, hole 10.0 4 = Aluminum CNC, U clevis, slot 6.0, depth 16.0, hole 6.4 5 = Aluminum CNC, U clevis, slot 6.0, depth 16.0, hole 8.0 Direction of Rear Attachment See page 10 Special Functions for Spindle SubAssembly 2 = Standard push only...

TA4 Ordering Key Appendix Retracted Length (mm) 1. Calculate A+B+C = Y 2. Retracted length needs to ≥ Stroke + Y A. Front Attachment

TA4 Ordering Key Appendix Rear Attachment (mm) 2 = luminum casting, U clevis, slot A 6.0, width 11.0, hole 8.0 3 = luminum casting, U clevis, slot A 6.0, width 11.0, hole 10.0 1 = luminum casting, U clevis, slot A 6.0, width 11.0, hole 6.4 Front Attachment (mm) 1 = Aluminum casting, hole 6.4 2 = Aluminum casting, hole 8.0 3 = luminum CNC, U clevis, slot 6.0, A depth 16.0, hole 10.0 4 = luminum CNC, U clevis, slot 6.0, A depth 16.0, hole 6.4 5 = luminum CNC, U clevis, slot 6.0, A depth 16.0, hole 8.0 Direction of Rear Attachment 1 = 0°

TA4 Ordering Key Appendix Functions for Limit Switches Wire Definitions CODE extend (VDC+) retract (VDC+) extend (VDC+) retract (VDC+) extend (VDC+) upper limit switch retract (VDC+) lower limit switch extend (VDC+) upper limit switch medium limit switch retract (VDC+) lower limit switch B = cable (for direct cut system, non water proof, non anti pull) Y L3 Cable length for direct cut system (mm) CODE Terms of Use The user is responsible for determining the suitability of TiMOTION products for a specific application. TiMOTION products are subject to change without prior notice.