Product Segments • Care Motion TiMOTION’s TA38M series linear actuator is specially designed for medical applications where a compact linear actuator is needed. The TA38M features a very slim design with a small installation size of only stroke plus 115mm (note 1), providing manufacturers great freedom during the design process. The palm-sized motor with up to 2000N force is excellent for all kinds of spacelimited products. Note 1: If stroke is from 20 to 45mm, the retracted length needs to ≥ 160mm. General Features Max. load Retracted length ≥ 160mm (depending on chosen options) Hall sensors Black, grey Operational temperature range

Standard Dimensions (mm) Retracted Length Load and Speed CODE Self Locking Force (N) Motor Speed (6000RPM, Duty Cycle 10%) B Note 1  Please refer to the approved drawing for the final authentic value. 2  The current & speed in table are tested with 24V DC motor. With a 12V DC motor, the current is approximately twice the current measured in 24V DC; speed will be similar for both voltages. 3  This self-locking force level is reached only when a short circuit is applied on the terminals of the motor. All the TiMOTION control boxes have this feature built-in. 4  The current & speed in table are...

Motor Speed (6000RPM, Duty Cycle 10%) Speed vs. Load 60.0 Performance Data (24V DC Motor)

Rear Attachment (mm) See page 5 E = luminum casting, U clevis, width 5.2, depth 12.2, A hole 6.2 G = luminum casting, U clevis, width 5.2, depth 12.2, A hole 8.2 Front Attachment (mm) See page 6 E = luminum casting, U clevis, width 5.2, depth 12.2, A hole 6.2 G = luminum casting, U clevis, width 5.2, depth 12.2, A hole 8.2 N = luminum casting, without slot, hole 6.2 A P = luminum casting, without slot, hole 8.2 A Direction of Rear Attachment (Counterclockwise) See page 6 Special Functions for Spindle SubAssembly 2 = Standard push only Functions for Limit Switches See page 6 1 = wo switches at...

TA38M Ordering Key Appendix Retracted Length (mm) 1. Calculate A+B = Y 2. Stroke 25~45mm, the retracted length needs to ≥ 160mm 3. Stroke 46~200mm, the retracted length needs to ≥ Stroke + Y 4. Code#E Standard stroke: Min. ≥ 40mm, tthe retracted length needs to ≥ S + 125mm A. Rear Attach. Front Attach. Rear Attachment (mm) E = luminum casting, U clevis, A width 5.2, depth 12.2, hole 6.2 G = luminum casting, U clevis, A width 5.2, depth 12.2, hole 8.2

TA38M Ordering Key Appendix Front Attachment (mm) G = luminum casting, U clevis, A width 5.2, depth 12.2, hole 8.2 N = luminum casting, without slot, A hole 6.2 P = luminum casting, without slot, A hole 8.2 ø8.2 E = luminum casting, U clevis, A width 5.2, depth 12.2, hole 6.2 Direction of Rear Attachment (Counterclockwise) 1 = 90° Functions for Limit Switches Wire Definitions CODE extend (VDC+) retract (VDC+) extend (VDC+) upper limit switch retract (VDC+)

TA38M Ordering Key Appendix Connector 1 = DIN 6P, 90° plug C = cable (For direct cut system, water proof, anti pull) Y Cable Length for Direct Cut System (mm) CODE P = olex 8P, 90° plug, without M anti-clip Q = olex 6P, 90° plug, without M anti-clip Terms of Use The user is responsible for determining the suitability of TiMOTION products for a specific application. TiMOTION products are subject to change without prior notice.