Product Segments • Care Motion • Ergo Motion TiMOTION's TA29 is one of our next generation medical DC linear actuators, which can lift up to 6000N, while maintaining a compact installation dimension. Its IP66W protection rating ensures durability and water resistance. The TA29 is highly recommended for various medical applications that require a short, retracted length, yet need to support a large force, such as the leg adjustment or sling angle actuator on the patient hoist system. Compact yet powerful, the TA29 is ideal for mobility-related medical equipment. Designed to reduce maintenance and increase comfort, this actuator enables smooth, safe motion for both patients and caregivers. It’s a trusted choice for manufacturers seeking durability and efficiency in a compact medical actuator. General Features Max. load Retracted length ≥ 178mm (depending on chosen options) Output signals Black, grey Operational temperature range Suitable for patient hoist applica

DrawingStandard Dimensions (mm) Load and Speed CODE Load (N) Push Pull Self Locking Force (N) No Load With Load No Load With Load Motor Speed (4800RPM, Duty Cycle 10%) Motor Speed (5200RPM, Duty Cycle 10%) 1 Please refer to the approved drawing for the final authentic value. 2 The current & speed in table are tested when the actuator is extending under push load. 3 This self-locking force level is reached only when a short circuit is applied on the terminals of the motor. All the TiMOTION control boxes have this feature built-in. 4 The current & speed in table are tested with 24V DC motor. With...

Motor Speed (4800RPM, Duty Cycle 10%) Speed vs. Load 35.0 Performance Data (24V DC Motor)

Motor Speed (5200RPM, Duty Cycle 10%) Speed vs. Load 35.0 Current vs. Load 8.0 7.0 6.0 5.0 Current (A) Performance Data (24V DC Motor)

Rear Attachment (mm) See page 7 3 = Aluminum casting, U clevis, slot 6.2, depth 12.2, hole 10.2 4 = Aluminum casting, U clevis, slot 6.2, depth 12.2, hole 12.2 Front Attachment (mm) See page 7 3 = Aluminum CNC, without slot, hole 10.2 Direction of Rear Attachment (Counterclockwise) See page 7 Special Functions for Spindle SubAssembly 0 = Without (Standard) 1 = Safety nut Functions for Limit Switches See page 8 1 = Two switches at full retracted / extended positions to cut current 2 = Two switches at full retracted / extended positions to cut current + third one in between to send signal 3 = Two...

qo t moTion Retracted Length (mm) 2. Retracted length needs to > Stroke + Y 3. Retracted length needs to > 178mm C. Spindle Functions Load (N) D. Output Signals P_POT +20

TA29 Ordering Key AppendixRear Attachment (mm) 3 = Aluminum casting, U clevis, slot 4 = Aluminum casting, U clevis, slot 6.2, depth 12.2, hole 10.2 6.2, depth 12.2, hole 12.2 Front Attachment (mm) 4 = Aluminum CNC, without slot, hole 12.2 3 = Aluminum CNC, without slot, hole 10.2

TA29 Ordering Key Appendix Functions for Limit Switches Wire Definitions CODE Pin • 1 (Green) 2 (Red) O 3 (White) 4 (Black) 5 (Yellow) A (Blue) 1 extend (VDC+) N/A N/A N/A retract (VDC+) N/A 2 extend (VDC+) N/A middle switch pin B middle switch pin A retract (VDC+) N/A 3 extend (VDC+) common upper limit switch N/A retract (VDC+) lower limit switch 4 extend (VDC+) common upper limit switch medium limit switch retract (VDC+) lower limit switch 5 extend (VDC+) N/A upper limit switch common retract (VDC+) lower limit switch C = Y cable (for direct cut system, water proof, anti pull) Cable Length...