Product Segments • Care Motion • Comfort Motion • Ergo Motion TiMOTION's TA19 series is a quiet and telescopic style linear actuator suited for height-adjustable work tables. The telescopic tube design of the TA19 linear actuator allows for a longer stroke with a shorter retracted length and reduced installation dimensions. This linear actuator can also be equipped with Hall sensors for position feedback. General Features Max. speed at max. load Max. speed at no load Retracted length Certificate Stroke Output signals Voltage Operational temperature range 1,000N (push) > Stroke / 2+165mm IEC60601-1, ES60601-1, EMC 180~800mm Hall sensors Suitable for height-adjustable work tables

Drawing Standard Dimensions (mm) Load and Speed Self Locking Force (N) No Load With Load No Load With Load Motor Speed (3800RPM, Duty Cycle 10%) Motor Speed (5200RPM, Duty Cycle 10%) Note 1 With a 12V motor, the current is approximately twice the current measured in 24V; speed will be similar for both voltages. 2 This self-locking force level is reached only when a short circuit is applied on the terminals of the motor. All the TiMOTION control boxes have this feature built-in. 3 Current and speed: Tested average value when stretching in push direction. 4 Standard stroke: 180~800mm, over 800mm,please...

Motor Speed (3800RPM, Duty Cycle 10%) Speed vs. Load Performance Data (24V DC Motor)

Motor Speed (5200RPM, Duty Cycle 10%) Speed vs. Load Performance Data (24V DC Motor)

Load and Speed See page 2 Retracted Length (mm) See page 6 Rear Attachment (mm) See page 7 Direction of Rear Attachment (Counterclockwise) 1 = Aluminum casting, U clevis, width 6.0, depth 12.5, hole 10.0 2 = Aluminum casting, U clevis, width 6.0, depth 12.5, hole 8.0 1 = Punched hole on the tube with plastic cover on, hole 10.0 2 = Punched hole on the tube with plastic cover on, hole 8.0 Special Functions for Spindle SubAssembly 1 = Two switches at full retracted / extended positions to cut current 2 = Two switches at full retracted / extended positions to cut current + third one in between to...

qo t moTion Retracted Length (mm)1. Calculate A+B = Y2. Retracted length needs to > Stroke / 2 + Y (3 stages) A. Rear/ Front Attachment B. Load V.S. Stroke Stroke (mm) * For stroke over 300mm, +10mm for each increment of 50mm stroke. Note 1 For stroke over 300mm, + 10 mm for each increment of 50mm stroke.

TA19 Ordering Key Appendix Rear Attachment (mm) 1 = Aluminum casting, U clevis, width 6.0, depth 12.5, hole 10.0 2 = Aluminum casting, U clevis, width 6.0, depth 12.5, hole 8.0 2 = Punched hole on the tube with plastic cover on, hole 8.0 1 = Punched hole on the tube with plastic cover on, hole 10.0 Direction of Rear Attachment (Counterclockwise) 1 = 90°

TA19 Ordering Key Appendix Functions for Limit Switches Wire Definitions CODE Pin • 1 (Green) 2 (Red) O 3 (White) 4 (Black) 5 (Yellow) A (Blue) 1 extend (VDC+) N/A N/A N/A retract (VDC+) N/A 2 extend (VDC+) N/A middle switch pin B middle switch pin A retract (VDC+) N/A 3 extend (VDC+) common upper limit switch N/A retract (VDC+) lower limit switch 4 extend (VDC+) common upper limit switch medium limit switch retract (VDC+) lower limit switch C = Y cable (direct cut, water proof, anti-pull) Cable length for direct cut system (mm) Terms of Use The user is responsible for determining the suitability...