Product Segments • Care Motion • Comfort Motion • Ergo Motion • Industrial Motion TiMOTION’s TA16 series linear actuator is similar to the TA2 linear actuator, but is specifically designed for low-noise applications where a compact linear actuator is needed. It is available with optional IP66 protection and Hall sensors for position feedback. Certificates for the TA16 include IEC60601-1, ES60601-1, IEC60601-1-2, UL962, and EMC. General Features Max. load Retracted length Stroke 20~600mm Output Signals Color Silver Operational temperature range at full performance With very low noise, small size for easy installation Suitable for patient hoist a

Dimensions without Output Signal or with Hall Sensors (mm)

Load and Speed CODE Self Locking Force (N) Motor Speed (3800RPM, Duty Cycle 10%) A Motor Speed (5200RPM, Duty Cycle 10%) G Note 1  Please refer to the approved drawing for the final authentic value. 2  This self-locking force level is reached only when a short circuit is applied on the terminals of the motor. All the TiMOTION control boxes have this feature built-in. 3  he current & speed in table are tested with 24V DC motor. With a 12V DC motor, the current is approximately twice the current T measured in 24V DC. With a 36V DC motor, the current is approximately two-thirds the current measured...

Motor Speed (3800RPM, Duty Cycle 10%) Speed vs. Load 60.0 Performance Data (24V DC Motor)

Motor Speed (5200RPM, Duty Cycle 10%) Speed vs. Load 60.0 Performance Data (24V DC Motor)

Rear Attachment (mm) See page 8 1 = luminum casting, U clevis, width 6.0, depth 12.2, hole 6.4, one piece casting with gear box A 2 = luminum casting, U clevis, width 6.0, depth 12.2, hole 8.0, one piece casting with gear box A 3 = luminum casting, U clevis, width 6.0, depth 12.2, hole 10.0, one piece casting with gear box A Front Attachment (mm) See page 8 1 = luminum casting, no slot, hole 6.4 A 2 = luminum casting, no slot, hole 8.0 A 3 = luminum casting, no slot, hole 10.0 A 4 = luminum casting, U clevis, width 6.0, depth 13.0, A hole 6.4 Direction of Rear Attachment (Counterclockwise) See...

TA16 Ordering Key Appendix Retracted Length (mm) 1. Calculate A+B+C+D = Y 2. Retracted length needs to ≥ Stroke + Y C. Load V.S. Spindle Functions A. Rear / Front Attach. Spindle Functions Load & Speed Type A, B, C, D, E, J, K Front Attach. Rear Attach. B. Load V.S. Stroke Stroke (mm) Load & Speed Type A, B, C, D, E, J, K

TA16 Ordering Key Appendix Rear Attachment (mm) 1 = luminum casting, U clevis, A width 6.0, depth 12.2, hole 6.4, one piece casting with gear box 2 = luminum casting, U clevis, A width 6.0, depth 12.2, hole 8.0, one piece casting with gear box 3 = luminum casting, U clevis, A width 6.0, depth 12.2, hole 10.0, one piece casting with gear box Front Attachment (mm) 2 = luminum casting, no slot, hole A 8.0 ø8 5 = luminum casting, U clevis, A width 6.0, depth 13.0, hole 8.0 6 = Aluminum casting, U clevis, width 6.0, depth 13.0, hole 10.0 4 = luminum casting, U clevis, A width 6.0, depth 13.0, hole...

TA16 Ordering Key Appendix Functions for Limit Switches Wire Definitions CODE extend (VDC+) retract (VDC+) extend (VDC+) retract (VDC+) extend (VDC+) upper limit switch retract (VDC+) lower limit switch extend (VDC+) upper limit switch medium limit switch retract (VDC+) lower limit switch C = Y cable (For direct cut system, water proof, anti pull) Cable Length for Direct Cut System (mm) Terms of Use The user is responsible for determining the suitability of TiMOTION products for a specific application. TiMOTION products are subject to change without prior notice.