Product Segments • Care Motion TiMOTION’s TA15 series linear actuator was specifically designed for bariatric bed applications. These beds require a robust, long life solution that incorporates safety, reliability and effortless operation. A significant feature of the TA15 linear actuator is the quick release function that allows for lowering of the patient in the event of an emergency or electrical power outage. General Features Max. load Retracted length Output signals POT, Reed, Hall sensors Black, grey Operational temperature range Quick relea

Standard Dimensions (mm) Load and Speed Push Pull Self Locking Force (N) No Load With Load No Load With Load Motor Speed (3000RPM, Duty Cycle 10%) Motor Speed (3800RPM, Duty Cycle 10%) 1 This self-locking force level is reached only when a short circuit is applied on the terminals of the motor. All the TiMOTION control boxes have this feature built-in. 2 The current & speed in table are tested with 24V DC motor. With a 12V DC motor, the current is approximately twice the current measured in 24V DC. With a 36V DC motor, the current is approximately two-thirds the current measured in 24V DC. Speed...

Performance Data (24V DC Motor) Motor Speed (3000RPM, Duty Cycle 10%)

Motor Speed (3800RPM, Duty Cycle 10%) Speed vs. Load 16.0 14.0 12.0 Performance Data (24V DC Motor)

Voltage 5 = 24V, thermal protector 7 = 36V, thermal protector Load and Speed See page 2 Retracted Length (mm) See page 6 1 = Iron CNC, U clevis, slot 8.2, depth 17.0, hole 10.2, 2 = Iron CNC, U clevis, slot 8.2, depth 17.0, hole 12.2 1 = Iron CNC, U clevis, slot 8.2, depth 17.0, hole 10.2, 2 = Iron CNC, U clevis, slot 8.2, depth 17.0, depth 17.0, 3 = Iron CNC, U clevis, slot 10.2, depth 17.0, hole 10.2, 4 = Iron CNC, U clevis, slot 10.2, depth 17.0, hole 12.2 3 = Iron CNC, U clevis, slot 10.2, depth 17.0, hole 10.2, 4 = Iron CNC, U clevis, slot 10.2, depth 17.0, hole 12.2 Direction of Rear Attachment...

TA15 Ordering Key Appendix Retracted Length (mm) 1. Calculate A+B+C = Y 2. Retracted length needs to ≥ Stroke+Y A. Front Attach. * For stroke over 300mm, +10mm for each increment of 50mm stroke. 4 = Iron CNC, U clevis, slot 10.2, depth 17.0, hole 12.2 3 = Iron CNC, U clevis, slot 10.2, depth 17.0, hole 10.2, T bushing 2 = Iron CNC, U clevis, slot 8.2, depth 17.0, hole 12.2 1 = Iron CNC, U clevis, slot 8.2, depth 17.0, hole 10.2, T bushing 4 = Iron CNC, U clevis, slot 10.2, depth 17.0, hole 12.2 3 = Iron CNC, U clevis, slot 10.2, depth 17.0, hole 10.2, T bushing 2 = Iron CNC, U clevis, slot 8.2,...

TA15 Ordering Key AppendixDirection of Rear Attachment (Counterclockwise)1 = 0° 3 = 90° Functions for Limit Switches Wire Definitions CODE Pin • 1 (Green) 2 (Red) O 3 (White) 4 (Black) 5 (Yellow) A (Blue) 1 extend (VDC+) N/A N/A N/A retract (VDC+) N/A 2 extend (VDC+) N/A middle switch pin B middle switch pin A retract (VDC+) N/A 3 extend (VDC+) common upper limit switch N/A retract (VDC+) lower limit switch 4 extend (VDC+) common upper limit switch medium limit switch retract (VDC+) lower limit switch 1 = DIN 6P, 90° plug 2 = Tinned leads F = DIN 6P 180° plug G = Audio plug _DD

TA15 Ordering Key Appendix Connector Q = Molex 6P, 90° plug Terms of Use The user is responsible for determining the suitability of TiMOTION products for a specific application. TiMOTION products are subject to change without prior notice.