Product Segments • Industrial Motion TiMOTION’s JP5 is an in-line linear actuator specifically designed for use in low-load industrial applications. With a maximum load capacity of 1,500N, it is particularly suitable for products and applications that require a compact installation space. The built-in current control board allows soft-start and softstop functionality in addition to overcurrent protection. Optional Hall sensors support synchronous operation and provide position feedback. With an IP rating up to IP69K, this actuator is well suited for the harshest of environments. General Features Max. load Retracted length Output signals Hall sensors Operational temperature range Operational temperature range at full performance Storage temperature range

Load and Speed CODE Self Locking Force (N) Motor Speed (8500RPM, Duty Cycle 20%) E Note 1 Please refer to the approved drawing for the final authentic value. 2 The current & speed in table are tested with 24V DC motor. With a 12V DC motor, the current is approximately twice the current measured in 24V DC. With a 36V DC motor, the current is approximately two-thirds the current measured in 24V DC. Speed will be similar for all the voltages. 3 The current & speed in table are tested when the actuator is extending under push load. 4 The current & speed in table and diagram are tested with a stable...

Motor Speed (8500RPM, Duty Cycle 20%) Speed vs. Load 35.0 Performance Data (12V DC Motor)

Rear Attachment (mm) See page 6 1 = Aluminum, slotless, hole 8.2 2 = Aluminum, slotless, hole 10.2 3 = Aluminum, U clevis, slot 4.2, depth 12.0, hole 8.2 4 = Aluminum, U clevis, slot 4.2, depth 12.0, hole 10.2 5 = Aluminum, U clevis, slot 6.2, depth 16.0, hole 8.2 6 = Aluminum, U clevis, slot 6.2, depth 16.0, hole 10.2 Front Attachment (mm) See page 6 1 = Aluminum, slotless, hole 8.2 2 = Aluminum, slotless, hole 10.2 3 = Aluminum, U clevis, slot 4.2, depth 12.0, hole 8.2 4 = Aluminum, U clevis, slot 4.2, depth 12.0, hole 10.2 5 = Aluminum, U clevis, slot 6.2, depth 16.0, hole 8.2 6 = Aluminum,...

JP5 Ordering Key Appendix Retracted Length (mm) 1. Calculate A+B+C = Y 2. Retracted length needs to ≥ Stroke + Y Case 1 A. Without Signal or Overcurrent Protection PCBA Front Attach. Rear Attach. A. Without Overcurrent Protection PCBA + with Hall Signal Front Attach. Rear Attach. A. With Hall Signal + Overcurrent Protection PCBA Front Attach. C. End of Stroke Over Current Protection PCBA 0

JP5 Ordering Key Appendix Rear Attachment (mm) 1 = Aluminum, slotless, hole 8.2 2 = Aluminum, slotless, hole 10.2 ø10.2 4 = Aluminum, U clevis, slot 4.2, depth 12.0, hole 10.2 5 = Aluminum, U clevis, slot 6.2, depth 16.0, hole 8.2 3 = Aluminum, U clevis, slot 4.2, depth 12.0, hole 8.2 6 = Aluminum, U clevis, slot 6.2, depth 16.0, hole 10.2 4 = Aluminum, U clevis, slot 4.2, depth 12.0, hole 10.2 ø20 3 = Aluminum, U clevis, slot 4.2, depth 12.0, hole 8.2 ø20 2 = Aluminum, slotless, hole 10.2 1 = Aluminum, slotless, hole 8.2 6 = Aluminum, U clevis, slot 6.2, depth 16.0, hole 10.2 ø20 5 = Aluminum,...

JP5 Ordering Key Appendix Connector 01 = Tinned leads Terms of Use The user is responsible for determining the suitability of TiMOTION products for a specific application. TiMOTION products are subject to change without prior notice.