Product Segments • Industrial Motion TiMOTION's JP3 series inline linear actuator was designed for low load industrial applications where up to IP69K dust and liquid ingress protection is necessary. It is best suited for applications with visual or compact installation dimension requirements. Hall sensors are optional for the JP3 which allow for synchronization and position feedback. General Features Max. load Retracted length Certificate UL73 Stroke 20~1000mm Voltage Operational temperature range Operational temperature range at full performance Storage temperature range An inline actuator designed for small

Standard Dimensions Load and Speed CODE Self Locking Force (N) Motor Speed (5600RPM, Duty Cycle 10%) B Note 1  Please refer to the approved drawing for the final authentic value. 2  Standard stroke: Min. ≥ 20mm, Max. please refer to below table 3  This self-locking force level is reached only when a short circuit is applied on the terminals of the motor. All the TiMOTION control boxes have this feature built-in. 4  The current & speed in table are tested with 24V DC motor. With a 12V DC motor, the current is approximately twice the current measured in 24V DC; speed will be similar for both voltages....

Motor Speed (5600RPM, Duty Cycle 10%) Speed vs. Load 30.0 Performance Data (24V DC Motor) Note 1  The performance data in the curve charts shows theoretical value.

Stroke (mm) Retracted Length (mm) Rear Attachment (mm) See page 6 1 = luminum casting, U clevis, slot 4.2, depth 18.0, hole 10.2 A Front Attachment (mm) See page 6 1 = luminum casting, no slot, hole 6.4 A 2 = Aluminum casting, no slot, hole 8.0 3 = luminum CNC, U clevis, slot 6.0, depth 13.0, hole 10.0 A 4 = luminum CNC, U clevis, slot 6.0, depth 13.0, hole 6.4 A 5 = luminum CNC, U clevis, slot 6.0, depth 13.0, hole 8.0 A 6 = Aluminum casting, hole 10.0 Direction of Rear Attachment (Counterclockwise) See page 6 Special Functions for Spindle SubAssembly Functions for Limit Switches See page 7...

JP3 Ordering Key Appendix Retracted Length (mm) 1. Calculate A+B+C = Y 2. Retracted length needs to ≥ Stroke + Y A. Front Attachment

JP3 Ordering Key Appendix Rear Attachment (mm) 1 = luminum casting, U clevis, slot A 4.2, depth 18.0, hole 10.2 11.7 Front Attachment (mm) 3 = luminum CNC, U clevis, slot 6.0, A depth 13.0, hole 10.0 5 = luminum CNC, U clevis, slot 6.0, A depth 13.0, hole 8.0 ø8 4 = luminum CNC, U clevis, slot 6.0, A depth 13.0, hole 6.4 2 = luminum casting, no slot, hole A 8.0 1 = luminum casting, no slot, hole A 6.4 6 = Aluminum casting, hole 10.0 9 Direction of Rear Attachment (Counterclockwise)

JP3 Ordering Key Appendix Functions for Limit Switches Wire Definitions Pin extend (VDC+) retract (VDC+) extend (VDC+) retract (VDC+) extend (VDC+) upper limit switch retract (VDC+) lower limit switch extend (VDC+) upper limit switch medium limit switch retract (VDC+) lower limit switch 100 250 PTC outside the motor; at cable length 100mm, min total cable = 250mm Terms of Use The user is responsible for determining the suitability of TiMOTION products for a specific application. TiMOTION products are subject to change without prior notice.