Group: Timken
Catalog excerpts
TIMKEN BALL BEARINGS CATALOG
Open the catalog to page 1TIMKEN BALL BEARINGS CATALOG
Open the catalog to page 2RADIAL AND ANGULAR CONTACT BEARINGS Overview: Timken is a premier manufacturer of ball bearings. We produce a broad range of precision ball bearings, wide inner ring ball bearings and housed units for standard industrial applications and specialized uses. From standard single-row deep groove radial ball bearings to advanced integral designs, Timken has your solution. • izes: 3 mm - 600 mm bore. S • arkets: Aircraft, construction, agriculture, machine tool and general industry. M • eatures: Special coatings for corrosion resistance, special seal designs. F • enefits: Radial: Better life in...
Open the catalog to page 4Radial and Angular Contact Ball Bearings F flanged outer ring J extra loose internal fit JJ extra extra loose internal fit S extra small inch-dimension type (same width inner and outer) WIR single-row, wide inner only Bore Size: (04 and up: multiply last two numbers by five to get FT full ball complement K Conrad, non-filling slot type W maximum capacity, filling slot type Wl angular contact, low-shoulder outer WO angular contact, low-shoulder inner WN angular contact, low-shoulder, Numbers: Basic Type Series: SI 3, 5, 7, etc., single-row inch, extra small 30 single-row metric, extra small...
Open the catalog to page 5Radial and Angular Contact Ball Bearings Radial Ball Bearings Page Page Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D4 Tri-Ply Seal Series, Non-Relubricatable Type Extra Small 30 Metric Series . . . . . . . . . . . . . . . . . . . . . . . . . . . D6 Extra Small 33 Series and S Inch Series . . . . . . . . . . . . . . . . . . D8 Tri-Ply Seal Series, Relubricatable Type . . . . . . . . . . . . . . . . . D29 F Flanged Series, Cylindrical and Tapered O.D. . . . . . . . . . . . . D9 Tri-Ply Seal Series, Disk Harrow Units . . . . . . . . . . . . . ....
Open the catalog to page 6BALL BEARINGS EXTRA SMALL SERIES Extra small bearings are available in the 30 Metric Series, the 33 and S Inch Series and the F Flanged Series. These bearings can sustain radial, thrust and combined loads proportionate to the capacities of the small shafts for which they are designed. They are appropriate for use in fractional horsepower motors, precision instruments, domestic appliances, film projectors and similar devices. The F flanged series has external shoulders with the bearing for mounting in through-bored housings. This series is used where compactness is essential or where it is...
Open the catalog to page 7Radial and Angular Contact Ball Bearings XLS AND EXTRA LARGE 100 SERIES Bearings in the inch-dimension XLS Series and metric-dimension Extra Large 100 Series have extra large diameters and a compact cross section. XLS bearings are made in the Conrad and maximum capacity filling slot designs. The Extra Large 100 Series offers the maximum capacity, filling slot and counterbore types. TRI-PLY SEAL DISK HARROW BEARINGS BearingswithTri-Ply Seals are designed for service involving severe contamination, such as disk harrows, disk tillers and other seed preparation equipment and certain conveyor...
Open the catalog to page 8EXTRA SMALL 30 METRIC SERIES • Designed for small shafts. • Can sustain radial, thrust and combined load proportionate to capacities of small shafts. • Suitable for use in fractional horsepower motors, domestic appliances, precision instruments and similar devices. • Offer various combinations of shields and seals, as listed • Electric motor quality for applications where quietness is • Stainless steel series, denoted by a prefix A before the bearing number. (Example: A38K) OPEN AND SHIELDED TYPES DIMENSIONS - TOLERANCES (1> Maximum shaft or housing fillet radius that bearing corners will...
Open the catalog to page 9Radial and Angular Contact Ball Bearings EXTRA SMALL 30 METRIC SERIES • Developed by The Timken® Company. • Adapted to the 30 metric series for effective grease retention and exclusion of foreign matter. • Can be operated at speeds comparable to open-type bearings. • Available with: • One Mechani-Seal and one shield (suffix LD). Bearing Number Ring Width I') Maximum shaft or housing fillet radius that bearing corners will clear I2) Does not apply to bearings with two seals. Note: Inner ring offset Is .51 mm (.020 Inches) for the L, LD, and VLD verslons. Seal Protection l3l Two seals (suffix...
Open the catalog to page 10BALL BEARINGS EXTRA SMALL 33 AND S INCH SERIES • Designed for small shafts. • Can sustain radial, thrust and combined loads, proportionate to capacities of small shafts. • Suitable for use in fractional horsepower motors, domestic appliances, precision instruments and similar devices. • Include combinations of shields and seals, as listed below. • Electric motor quality for applications where quietness is • Several sizes are manufactured both in standard bearing-quality steel and stainless steel, as indicated in the tables. l'I Maximum shaft or housing fillet radius that bearing corners...
Open the catalog to page 11Radial and Angular Contact Ball Bearings FLANGED SERIES • Four sizes offered in flanged construction. • Integral shoulders for mounting in through-bored housings. • Straight outside diameters. • Interchangeable with corresponding unflanged sizes. • Available with double shields. • Electric motor quality for applications where quietness Open Type Shielded Type "I Also available In stainless steel. To specify, add preflx'A" before bearing number l2l Based on 106 revolutions of calculated fatigue life •Also available with two contact seals. To specify, replace "KDD" In part number with "PP". •...
Open the catalog to page 12BALL BEARINGS Pressed steel housed units designed for light-duty applications. Available in shaft sizes from 6.35 mm -12.7 mm PA to V2 inch). Designed to simplify mounting on side plate or frame-type housings. Two identical steel stampings house a clamp-type bearing with a spherical O.D. outer ring. Spherical inside surface of each stamping mates with the spherical O.D. of the bearing, providing initial self-alignment at mounting. Offers features of basic clamp-type bearing. Available with sealed or shielded construction. Radial load capacity is 25 percent of basic bearing's dynamic load...
Open the catalog to page 13All TIMKEN catalogs and technical brochures
-
QUICK FLEX® Couplings
56 Pages
-
COMPETENCYBASED TRAINING
5 Pages
-
National® Industrial Seals
716 Pages
-
TIMKEN® ECOTURN® SEAL
2 Pages
-
Timken® Lubricants
6 Pages
-
Quick-Flex Couplings
68 Pages
-
Matched Bearing Assemblies
16 Pages
-
Cylindrical Roller Bearings
108 Pages
-
AP Bearings
84 Pages
-
Spherical Roller Bearings
236 Pages
-
UC Series Ball Housed Units
24 Pages
-
Type E Housed Units
40 Pages
-
Ball Housed Units
180 Pages
-
SNT Plummer Blocks
120 Pages
-
SAF Housed Units
126 Pages
-
Thrust Bearings
138 Pages
-
Quick-Flex Coupling Catalog
68 Pages
-
Bearing interchange guide
163 Pages
-
UC-SERIES
24 Pages
-
Quick-Flex Coupling
64 Pages
-
Timken Drives Roller Chain Catalog
112 Pages
-
Commercial Vehicle Catalog
417 Pages
-
Industrial Maintenance Manual
157 Pages
-
Timken SAF Housed Unit Catalog
126 Pages
-
Timken Ball Housed Unit Catalog
180 Pages
-
Timken® SNT Plummer Block Catalog
120 Pages
-
BALL BEARINGS
214 Pages
-
Timken Engineering Manual
210 Pages
-
Timken Industrial Seals
40 Pages
Archived catalogs
-
Ball Bearings
6 Pages
-
IsoClass Bearings
8 Pages
-
Maintenance Tools
16 Pages
-
Industrial Products
56 Pages
-
Precision Rotary Assemblies
2 Pages
-
Ceramic Bearings
2 Pages