Catalogs >
TIMKEN Europe >
Timken Ball Bearings

Timken Ball Bearings
217Pages

Add to favorites

Catalog excerpts

CYLINDRICAL ROLLER BEARING CATALOG TIMKEN BALL BEARINGS CATALOG

Open the catalog to page 1

CYLINDRICAL ROLLER BEARING CATALOG TIMKEN BALL BEARINGS CATALOG

Open the catalog to page 2

BALL BEARINGS TIMKEN PRODUCTS CATALOG TIMKEN SERVICE

Open the catalog to page 3

RADIAL AND ANGULAR CONTACT BEARINGS Overview: Timken is a premier manufacturer of ball bearings. We produce a broad range of precision ball bearings, wide inner ring ball bearings and housed units for standard industrial applications and specialized uses. From standard single-row deep groove radial ball bearings to advanced integral designs, Timken has your solution. • izes: 3 mm - 600 mm bore. S • arkets: Aircraft, construction, agriculture, machine tool and general industry. M • eatures: Special coatings for corrosion resistance, special seal designs. F • enefits: Radial: Better life in...

Open the catalog to page 4

Radial and Angular Contact Ball Bearings Prefixes: A stainless steel F flanged outer ring H snug fit J extra loose internal fit JJ extra extra loose internal fit L internal self-aligning M precision ABEC 3 P loose fit R normal fit S extra small inch-dimension type T tight fit V precision ABEC 5 W wide-type single-row (same width inner and outer) WIR single-row, wide inner only Bore Size: (04 and up: multiply last two numbers by five to get bore in millimeters) 00 10 mm 01 12 mm 02 15 mm 03 17 mm 04 20 mm 05 25 mm 12 60 mm 20 100 mm Numbers: Basic Type Series: S1 3, 5, 7, etc., single-row...

Open the catalog to page 5

Radial and Angular Contact Ball Bearings Radial Ball Bearings Tri-Ply Seal Series, Non-Relubricatable Type Extra Small 30 Metric Series . . . . . . . . . . . . . . . . . . . . . . . . . . . D6 Extra Small 33 Series and S Inch Series . . . . . . . . . . . . . . . . . . D8 Tri-Ply Seal Series, Relubricatable Type . . . . . . . . . . . . . . . . . D29 F Flanged Series, Cylindrical and Tapered O.D. . . . . . . . . . . . . D9 Tri-Ply Seal Series, Disk Harrow Units . . . . . . . . . . . . . . . . . . D30 RTF-Rubber Tire Flanged Housed Unit . . . . . . . . . . . . . . . . . . D10 Light 200 Series,...

Open the catalog to page 6

BALL BEARINGS INTRODUCTION EXTRA SMALL SERIES Extra small bearings are available in the 30 Metric Series, the 33 and S Inch Series and the F Flanged Series. These bearings can sustain radial, thrust and combined loads proportionate to the capacities of the small shafts for which they are designed. They are appropriate for use in fractional horsepower motors, precision instruments, domestic appliances, film projectors and similar devices. The F flanged series has external shoulders with the bearing for mounting in through-bored housings. This series is used where compactness is essential or...

Open the catalog to page 7

Radial and Angular Contact Ball Bearings XLS AND EXTRA LARGE 100 SERIES Bearings in the inch-dimension XLS Series and metric-dimension Extra Large 100 Series have extra large diameters and a compact cross section. XLS bearings are made in the Conrad and maximum capacity filling slot designs. The Extra Large 100 Series offers the maximum capacity, filling slot and counterbore types. XLS and Extra Large 100 Series TRI-PLY SEAL DISK HARROW BEARINGS Bearings with Tri-Ply Seals are designed for service involving severe contamination, such as disk harrows, disk tillers and other seed preparation...

Open the catalog to page 8

BALL BEARINGS Extra Small 30 Metric Series • Offer various combinations of shields and seals, as listed below. • Electric motor quality for applications where quietness is required. • Stainless steel series, denoted by a prefix A before the • Designed for small shafts. • Can sustain radial, thrust and combined load proportionate to capacities of small shafts. • Suitable for use in fractional horsepower motors, domestic appliances, precision instruments and similar devices. bearing number. (Example: A38K) Open and shielded types dimensions – tolerances Bearing Number Bore Outside Width...

Open the catalog to page 9

Radial and Angular Contact Ball Bearings Extra Small 30 Metric Series MECHANI-SEALS • Developed by The Timken Company. • Adapted to the 30 metric series for effective grease retention and exclusion of foreign matter. • Can be operated at speeds comparable to open-type bearings. • Available with: ® • One Mechani-Seal (suffix L). • One Mechani-Seal and one shield (suffix LD). • Two Mechani-Seals (suffix LL). One Seal One Seal and Shield L LD Inner Wt. Fillet Seal Protection (1) DIMENSIONS – TOLERANCES Bearing Number Bore d one +0.000 mm seal one and two -0.008 mm seal shield seals +0.0000" L...

Open the catalog to page 10

BALL BEARINGS Extra Small 33 and S Inch Series • Designed for small shafts. • Can sustain radial, thrust and combined loads, proportionate to capacities of small shafts. • Suitable for use in fractional horsepower motors, domestic appliances, precision instruments and similar devices. • Include combinations of shields and seals, as listed below. • Electric motor quality for applications where quietness is required. • Several sizes are manufactured both in standard bearing-quality steel and stainless steel, as indicated in the tables. DIMENSIONS – TOLERANCES Bearing Number Bore Outside Width...

Open the catalog to page 11

Radial and Angular Contact Ball Bearings E Flanged Series CYLINDRICAL O.D. • Four sizes offered in flanged construction. • Integral shoulders for mounting in through-bored housings. • Straight outside diameters. • Interchangeable with corresponding unflanged sizes. • Available with double shields. • Electric motor quality for applications where quietness Open Type Shielded Type DIMENSIONS – TOLERANCES Bearing Number Bore Outside Width Inner Ring Flange Shielded Type Wt. Static Extended d Diameter C Shoulder Overall Load Dynamic chamfer D Width Rating Load Rating J x 45° A CO +0.000 mm +0.25...

Open the catalog to page 12

BALL BEARINGS ST Flangette Unit • Pressed steel housed units designed for light-duty applications. • Available in shaft sizes from 6.35 mm - 12.7 mm (1/4 to 1/2 inch). • Designed to simplify mounting on side plate or frame-type housings. • Two identical steel stampings house a clamp-type bearing with a spherical O.D. outer ring. • Spherical inside surface of each stamping mates with the spherical O.D. of the bearing, providing initial self-alignment at mounting. • Offers features of basic clamp-type bearing. • Available with sealed or shielded construction. • Radial load capacity is 25...

Open the catalog to page 13