Manual telescopic slides

Product catalog summary

Introduction
This manual provides guidance on the installation of telescopic ball bearing slides manufactured by Thomas Regout International B.V. It emphasizes the importance of correct installation for maximizing service life and offers contact information for further assistance.

General Specifications
The slides are produced in the Netherlands and are designed for various applications. The nominal overall dimension of the slide should be considered during installation, with a thickness of the slide plus 0.5 mm ± 0.25 mm. A minimum clearance of 5 mm behind the drawer is recommended.

Installation and Alignment
Accurate alignment of the slides is crucial to prevent them from working against each other. The handle should be mounted centrally on the drawer for optimal performance. Slides should be installed in a rigid construction and are tested for a maximum width of 600 mm. For wider drawers, consultation with the company is advised.

Load Capacity
Load capacities are indicative and depend on usage type: static (less than 10,000 cycles) and dynamic (up to 60,000 cycles). Factors affecting performance include load distribution, center of gravity, movement speed, slide length, and force against the end stop. Regular full extension of slides is recommended for optimal performance.

Fixation
Various fixation methods are available, and care should be taken to ensure screw heads do not interfere with slide movement. Recommendations for standard products are available on the company's website.

Environmental Considerations
Slides are corrosion-resistant but should be protected from high humidity, salts, and chemicals. Grease is applied for optimal performance, but contaminants can reduce its effectiveness.

Maintenance and Safety
The slides are maintenance-free. Safety precautions, such as wearing gloves, are recommended during assembly to prevent injury from moving parts.

Contact Information
For more information, contact Thomas Regout International B.V. at their Maastricht location or through their website.

Catalog excerpts

telescopic slides

Open the catalog to page 1

Thank you for purchasing a product from Thomas Regout International B.V. This manual covers the installation of telescopic ball bearing slides. If you have questions, please contact your salesperson or visit www.thomasregout.com. General This manual pertains to all telescopic ball bearing slides produced by Thomas Regout International B.V. at our factory in the Netherlands. Correct installation ensures maximum service life. We will be happy to help you select the correct slide for your specific application. Overall dimension When installing a slide, the nominal overall dimension of the slide...

Open the catalog to page 2

Ideal installation situation Front view Front view Alignment When positioning the slides, it is important that they are aligned accurately, within the specified tolerances. The more precisely the guide rails are aligned, the smaller the chance that the slides will work against each other.

Open the catalog to page 3

Our slides perform best when mounted in a very rigid construction (furniture, device or installation). Do not use the drawer slides as a structural part of a construction. Dimensions Our slides are tested at a maximum width of 600 mm. If you have a drawer wider than 600 mm, please contact us to discuss the possibilities we can offer you. Handle The mounting position of the handle affects the performance of the slides. It is recommended that the handle be attached in the centre of the drawer (as shown).

Open the catalog to page 4

Drawer slides can be mounted using a wide variety of fixations such as screw holes, mounting tabs, hanging tabs, press-in bolts, etc. When selecting screws, make sure the screw head does not protrude, so there is no contact between the moving parts of the slide and the screw head. For our standard products, fixation recommendations are available on our website: www.thomasregout.com. 3x The screwholes are accessible by mounting holes. Load capacity Thomas Regout International B.V. distinguishes between two types of usage: dynamic use and static use. Load capacities are specified per pair and are...

Open the catalog to page 5

Abnormal loads / vibrations Transport, misuse and shock loads – even of short duration – may cause damage. Excessive or continuous vibration can also reduce the performance and service life of the slides. Thomas Regout International B.V. Our slides have a corrosion-resistant, zinc-plated, bluepassivated finish. High humidity, salts or other chemical agents may damage the surface of metal or plastic components. Exposure to any such conditions should be avoided at all times. Industrieweg 40 6219 NR Maastricht The Netherlands To ensure optimum performance, Thomas Regout International B.V. applies...

Open the catalog to page 6