1. Catalogs
  2. Thermik
  3. e1 - Thermal-Protectors with epoxy coating

e1 - Thermal-Protectors with epoxy coating

e1 - Thermal-Protectors with epoxy coating

e1 - Thermal-Protectors with epoxy coating

Product catalog summary
Specifications:
Diameter: 10.1 mm
Height: 4.0 mm
Type: e1 Thermal Protector
Contact Type: Normally Closed (NC)
Nominal Switching Temperature (NST): 70°C – 160°C in steps of 5 K
Standard Tolerance: ± 5 K
Resetting Temperature (RST): > 35°C
Operating Voltage: 100V up to 500 V AC/DC
Rated Voltage: 250 V AC (at 50Hz – 60Hz)
Rated Current: 2.5A (cos ϕ = 1.0) and 1.6 A (cos ϕ = 0.6) for 10,000 cycles
Max. Switching Current: 5.0 A (cos ϕ = 1.0) for 300 cycles
Contact Bounce Time: < 1 ms
Contact Resistance: < 50 mΩ
Vibration Proof: 10 - 60 Hz, 100 m/s²
Pressure Stability: 150 N
Switch Insulation: Epoxy Coating
Dielectric Strength: 1,450 V
Standard Connection Leads: Multi-stranded wire 0.25 mm²
Approvals: VDE, CB Scheme
Application:
The e1 Thermal Protectors are used for overheating protection in electrical equipment such as motors, heaters, and transformers. They can be installed on or embedded inside windings and are suitable for small spaces due to their compact size.
Design:
The e1 version features an epoxy coating for optimal thermal transfer and built-in base insulation. The insulation is marked with the manufacturer logo, type, and nominal switching temperature with tolerance.
Operation:
Upon reaching the rated switching temperature, the bimetallic disc snaps open the contacts. It resets and recloses the contacts after cooling to the resetting temperature.
Features:
- Small dimensions suitable for compact applications
- High response sensitivity due to small mass and metal housing
- Excellent long-term performance with reproducible switching temperature values
- Very short bouncing times (< 1 ms)
- Instantaneous switching with constant contact pressure
- Temperature resistance due to high-temperature materials
Ordering Information:
The e1 Thermal Protector is available with white and yellow lead wires. Minimum order quantity is 10,000 pieces, and it can only be ordered directly from Thermik.
Additional Notes:
Values may differ for special designs, and technical specifications are subject to change without notice.
See more

Catalog excerpts

e1 - Thermal-Protectors with epoxy coating-1

Thermal Protectors (TP) of version e1 with normally closed contacts are standard versions, utilised for overheating protection of all kinds of electrical equipments or devices, e. g. for electric motors, heaters and transformers. They can either be installed on or embedded inside the windings. Due to their small overall dimensions, they will fit even in smallest space. > Diameter The version e1 has an epoxy coating for best thermal transfer to the housing. Therefore when fitting ֖ the base insulation of the switch is provided and does not need to be done by the customer. The insulation is marked with the manufacturer logo, type and the nominal switching temperature with its tolerance. > d 10.1 mm Height h 4.0 mm dimensions (average) If, in case of overheating, the rated switching temperature of the bimetallic disc is reached, it suddenly snaps over to open the contacts. After cooling down to the resetting temperature, the bimetallic disc resets and causes the contacts to reclose. . > Smallest dimensions: therefore suitable for smallest applications High response sensitivity: featured by small protector mass and the metal - housing Excellent long term performance : performance of reproducible switching temperature values due to instantaneous switching, fine-silver contacts, constant contact resistance and to electrically as well as mechanically unstressed bimetallic disc Very short bouncing times: < 1 ms Instantaneous switching: with constant contact pressure over the whole temperature range Temperature resistance: by use of high temperature resistant materials and components > Thermik Gertebau GmbH ? Im Altgefll 8 ? D-75181 Pforzheim ? Germany ? Phone: +49 (72 31) 60 04 -0 ? Fax: +49 (72 31) 60 04-100 size="-2">

 Open the catalog to page 1
e1 - Thermal-Protectors with epoxy coating-2

Type e1 125 > 5 Rated switching temperature [ҰC] , > Tolerance [K] : e1 . 125 . 05 . 0100 / 0100 Type and versionRated switching temperature [ C ]Tolerance [ K ]Lead lengths [ mm ] > The indicated values in this data sheet can differ for special designs. We reserve the right to modify technical specifications without notice. Rev.:20.01.2009 size="-2">

 Open the catalog to page 2

Archived catalogs

*Prices are pre-tax. They exclude delivery charges and customs duties and do not include additional charges for installation or activation options. Prices are indicative only and may vary by country, with changes to the cost of raw materials and exchange rates.