I Magnetostrictive Linear Position Sensors I Stroke length up to 5000 mm I Linearity < 0.04 % F.S. / Resolution typ. 0.1 mm I High reliability due to EMC, shock & vibration resistance Americas & APAC

Temposonics® MH-Series EMBEDDED CANbus Data Sheet The absolute, linear position sensors provided by Temposonics rely on the company’s proprietary magnetostrictive technology, which can determine position with a high level of precision and robustness. Each Temposonics® position sensor consists of a ferromagnetic waveguide, a position magnet, a strain pulse converter and supporting electronics. The magnet, connected to the object in motion in the application, generates a magnetic field at its location on the waveguide. A short current pulse is applied to the waveguide. This creates a momentary...

Temposonics® MH-Series EMBEDDED CANbus Data Sheet */ Resonance frequencies excluded Continued on the next page

Temposonics® MH-Series EMBEDDED CANbus Data Sheet **/ According to calculations under use of the FKM guideline Cycles 0 7 mm sensor rod 0 10 mm sensor rod Dynamic pressure: > 2 x 106 pressure cycles 300 bar 350 bar Static pressure: > 2 x 104 pressure cycles 400 bar 450 bar Proof pressure: Maximum 5 minutes testing time for cylinder pressure test 625 bar 625 bar

Temposonics® MH-Series EMBEDDED CANbus Data Sheet TECHNICAL DRAWING MH-C – Rod: Ø 10 mm/Dead zone: 63.5 mm/Stroke length: 50…5000 mm Stroke length 50…5000 MH-D – Rod: Ø 7 mm/Dead zone: 63.5 mm/Stroke length: 50…4000 mm Stroke length 50…4000 MH-E – Rod: Ø 10 mm/Dead zone: 36.5 mm/Stroke length: 50…1200 mm Stroke length 50…1200 Controlling design dimensions are in millimeters Fig. 4: Temposonics® MH-Series EMBEDDED sensor, part 1

Temposonics® MH-Series EMBEDDED CANbus Data Sheet MH-F – Rod: Ø 7 mm/Dead zone: 36.5 mm/Stroke length: 50…1200 mm Stroke length 50…1200 MH-L – Rod: Ø 10 mm + end plug with female M6 thread Dead zone: 69.5 mm/Stroke length: 50…5000 mm Stroke length 50…5000 MH-R – Rod: Ø 10 mm + end plug with female M4 thread/Dead zone: 69.5 mm/Stroke length: 50…5000 mm Dead zone 69.5 Controlling design dimensions are in millimeters Fig. 5: Temposonics® MH-Series EMBEDDED sensor, part 2

Temposonics® MH-Series EMBEDDED CANbus Data Sheet MH-Q – Rod: Ø 10 mm/Dead zone: 85.5 mm/Stroke length: 2520…5000 mm Null zone 30 MH-C with conical end plug “K1” for Ø 10 mm Stroke length 50…5000 Detail view of endplug 21.2 30 MH-D with conical end plug “K1” for Ø 7 mm Stroke length 50…4000 Detail view of endplug 21.2 30 Controlling design dimensions are in millimeters Fig. 6: Temposonics® MH-Series EMBEDDED sensor, part 3

Temposonics® MH-Series EMBEDDED CANbus Data Sheet MH-E with conical end plug “K1” for Ø 10 mm Stroke length 50…1200 Detail view of endplug 21.2 30 MH-F with conical end plug “K1” for Ø 7 mm Stroke length 50…1200 Detail view of endplug 21.2 30 Controlling design dimensions are in millimeters Fig. 7: Temposonics® MH-Series EMBEDDED sensor, part 4

Data Sheet CONNECTOR WIRING(1) M12 connector system without flange (K ...F) & (2) with flange (N...F) Single lead wires 0.22 mm2 Attached A-coded M12 connector Toolless Assembly Sealing IP67, up to IP69K with mating connector Single lead wires 0.22 mm2 Attached A-coded M12 connector attached Toolless assembly Sealing IP67, up to IP69K with mating connector Based on DIN EN 61076-2-101 Pin Wire Function Pin Wire Function 1 - not connected Controlling design dimensions are in millimeters

Data Sheet • Single lead wires 0.5 mm2 (1) DT connector system (A...S) & (2) Interconnect without DT connector system (W...S) Single lead wires 0.22 mm2 4 pin DT style connector Toolless Assembly Sealing IP67, up to IP69K with mating connector Connector wiring Pin Function 60...240 Controlling design dimensions are in millimeters

Temposonics® MH-Series EMBEDDED CANbus Data Sheet MECHANICAL INSTALLATION MECHANICAL INSTALLATION – POSITION MAGNET Magnet installation e.g. retaining with set screw (with flat point) ISO 4026 M5×10 (DIN 913). Fastening torque: ≤ 0.5 Nm Non-magnetic spacer Position magnet NOTICE Avoid sensor damage: • The screw may touch the sensor housing. • Tightening torque: ≤ 0.5 Nm. Lock set screw: • Lock the set screw against falling out. • Make sure that the threads are free of oil, grease and dirt. Sealing: • Consider a seal against water ingress (capillary effect). Non-magnetic spacer (≥ 5 mm) Position...

Temposonics® MH-Series EMBEDDED CANbus Data Sheet MECHANICAL INSTALLATION FOR STROKE LENGTHS GREATER THAN 2.5 M – SUPPORT TUBE For enhanced stability of the Sensor rod with sensors longer than 2.5 m, Temposonics® proposes to use a support tube assembly as shown below. Support tubes can be used only with MH model MHQ and the magnets displayed in the table on this page. For further design information please consult the Installation Manual for MH-Series sensors. Support tube MECHANICAL INSTALLATION – POSITION MAGNET Position magnets (please order separately) for installation with support tube Operating...

ORDER CODE □□□ □ Sensor model M H Pressure fit flange Order code continued on next page

Temposonics® MH-Series EMBEDDED CANbus Data Sheet • Position sensor Accessories (e.g. position ^ • O-ring magnets) have to be ordered • Backup-ring separately • M12 connector system incl. M12 flange (when option selected) • DT connector system incl. connector assembly and retainer (when option selected)

Temposonics® MH-Series EMBEDDED CANbus Data Sheet FREQUENTLY ORDERED ACCESSORIES Position magnets Ring magnet OD17.4 Part no. 401 032 Ring magnet OD25.4 Part no. 400 533 Ring magnet OD33 Part no. 201 542-2 Testkit CANbus Part no. 253 879 Material: PA neobond Weight: Approx. 5 g Surface pressure: Max. 20 N/mm2 Operating temperature: −40…+105 °C (−40…+221 °F) Material: PA ferrite Weight: Approx. 10 g Surface pressure: Max. 40 N/mm2 Operating temperature: −40…+120 °C (−40…+248 °F) Material: PA 66-GF33 Weight: Approx. 14 g Surface pressure: Max. 40 N/mm2 Fastening torque for M4 screws: 1 Nm Operating...