MH-Series COMPACT Analog/CANbusMagnetostrictive Linear Position Sensors I Compact sensor housing I High reliability due to EMC, shock & vibration resistance

Temposonics® MH-Series COMPACT Analog/CANbus Data Sheet MEASURING TECHNOLOGY Position magnet (Magnetic field) 2 The absolute, linear position sensors provided by Temposonics rely on the company’s proprietary magnetostrictive technology, which can determine position with a high level of precision and robustness. Each Temposonics® position sensor consists of a ferromagnetic waveguide, a position magnet, a strain pulse converter and supporting electronics. The magnet, connected to the object in motion in the application, generates a magnetic field at its location on the waveguide. A short current...

Temposonics® MH-Series COMPACT Analog/CANbus Data Sheet */ Resonance frequencies excluded **/ According to calculations under use of the FKM guideline Dynamic pressure: > 2 x 106 pressure cycles 300 bar Static pressure: > 2 x 104 pressure cycles 400 bar Proof pressure: Maximum 5 minutes testing time for cylinder pressure test 525 bar

Temposonics® MH-Series COMPACT Analog/CANbus Data Sheet

Temposonics® MH-Series COMPACT Analog/CANbus Data Sheet */ Resonance frequencies excluded **/ According to calculations under use of the FKM guideline Dynamic pressure: > 2 x 106 pressure cycles 300 bar Static pressure: > 2 x 104 pressure cycles 400 bar Proof pressure: Maximum 5 minutes testing time for cylinder pressure test 525 bar

Data Sheet Connection type M12 connector or DT connector system or single wires or cable outlet Operating voltage 12/24 VDC nominal (8...32 VDC) Max Inrush current 1.5 A/2 ms (1.0 A/2 ms if supply > 13 V) Supply voltage ripple < 1 % PP Over voltage protection (GND-VDC) Up to +36 VDC Polarity protection (GND-VDC) Up to -36 VDC Electric strength 500 VDC (DC GND to chassis GND)

Temposonics® MH-Series COMPACT Analog/CANbus Data Sheet TECHNICAL DRAWING MS-D – Dead zone: 63.5 mm / Stroke length: 50…2500 mm Stroke length 50…2500 MS-F – Dead zone: 36.5 mm / Stroke length: 50…1200 mm Stroke length 50…1200 40.9 Controlling design dimensions are in millimeters Fig. 4: Temposonics® MH-Series COMPA

Data Sheet • Single lead wires 0.22 mm2 • Attached A-coded M12 connector attached • Toolless assembly • Sealing IP67, up to IP69K with plugged mating connector Connector wiring M12 connector system (N...G) • Single lead wires 0.22 mm2 • Attached A-coded M12 connector attached • Toolless assembly • Sealing IP67, up to IP69K with plugged mating connector M12 connector system (N...H) • Single lead wires 0.22 mm2 • Attached A-coded M12 connector attached • Toolless assembly • Sealing IP67, up to IP69K with plugged mating connector Connector wiring Single wires pigtail (N...A) • Single lead wires...

Temposonics® MH-Series COMPACT Analog/CANbus Data Sheet Pigtail cable (T…A) • TPE cable black 3 × 24 AWG (0.34mm2) • Ø 5 mm, non-shielded, 3 × 0.5 mm2 • Flexible, oil resistance Connector wiring 8 Single lead wires 0.22 mm2 Attached DT compatible connector Sealing IP69K (with or without mating connector) Wiring sequence controlled at sensor 2 Single lead wires 0.22 mm2 Attached DT compatible connector Sealing IP69K (with or without mating connector) Wiring sequence controlled at sensor 2 Connector wiring • Single lead wires 0.22 mm2 • Attached DT compatible connector • Sealing IP69K (with or...

Data Sheet Single lead wires 0.22 mm2 Attached A-coded M12 connector attached Toolless assembly Sealing IP67, up to IP69K with plugged mating connector Connector wiring Single wires pigtail (N...A) • Single lead wires 0.5 mm2 Pigtail cable (T...A) • PUR cable, black DT connector system S (A...S) Single lead wires 0.22 mm2 Attached DT compatible connector Sealing IP69K (with or without mating connector) Wiring sequence controlled at sensor Connector wiring

Temposonics® MH-Series COMPACT Analog/CANbus Data Sheet MECHANICAL INSTALLATION MECHANICAL INSTALLATION - POSITION MAGNET Magnet installation To Avoid sensor damage: • Do not select a screw with a sharp point • M5 or M4 screw (with flat or cup end) are typically used • For M5, ensure that the screw lands on the angled side of the set screw channel • Note: M5 screw may not seat completely into the set screw channel, but will properly retain the sensor M4 screw (with flat or cup end) will seat completely • It is recommended to seal the set screw cavity against water © Non-magnetic spacer © Position...

Data Sheet • Position sensor Accessories (e.g. position • O-ring magnets) have to be ordered • Backup-ring separately • M12 connector system incl. M12 flange (when option selected) • DT connector system incl. connector assembly and retainer (when option selected) Manuals, Software & 3D models available at: www.temposonics.com

Data Sheet Sensor model Examples wire length N06F = 60 mm Connector wiring: F: 2-3-4-5 Single wires 40.240 mm wire length (in 20 mm steps) Examples wire length N20A = 200 mm Cable outlet 300...9900 mm cable length (in 100 mm steps) Examples wire length T10A = 1000 mm 60.240 mm wire length (in 20 mm steps) Examples wire length N22S = 220 mm Connector wiring: 1-3-4-2 • Position sensor Accessories (e.g. position ^ • O-ring magnets) have to be ordered • Backup-ring separately • M12 connector system incl. M12 flange (when option selected) • DT connector system incl. connector assembly and retainer...

Temposonics® MH-Series COMPACT Analog/CANbus Data Sheet FREQUENTLY ORDERED ACCESSORIES Position magnets Ø 32.8 Ring magnet OD17.4 Part no. 401 032 Ring magnet OD25.4 Part no. 400 533 Ring magnet OD33 Part no. 201 542-2 Material: PA neobond Weight: Approx. 5 g Surface pressure: Max. 20 N/mm2 Operating temperature: −40…+105 °C (−40…+221 °F) Material: PA ferrite Weight: Approx. 10 g Surface pressure: Max. 40 N/mm2 Operating temperature: −40…+120 °C (−40…+248 °F) Material: PA ferrite GF20 Weight: Approx. 14 g Surface pressure: Max. 40 N/mm2 Fastening torque for M4 screws: 1 Nm Operating temperature:...