Catalogs >
Teledyne LeCroy Europe >
Oscilloscope Probes and Probe Accessories

Oscilloscope Probes and Probe Accessories
56Pages

Catalog excerpts

Oscilloscope Probes and Probe Accessories

PROBE SELECTION GUIDE Learn More: teledynelecroy.com/probes Teledyne LeCroy has a wide variety of world class probes and amplifiers to compliment its product line. From the ZS high impedance active probes to the WaveLink differential probing system which offers bandwidths up to 25 GHz, Teledyne LeCroy probes and probe accessories provide optimum mechanical connections for signal measurement. HDO4000A High Definition Oscilloscopes HDO6000A High Definition Oscilloscopes HDO8000A High Definition Oscilloscopes / MDA800A Motor Drive Analyzers HDO9000 High Definition Oscilloscopes WaveJet...

Open the catalog to page 2

Oscilloscope Probes and Probe Accessories - 3

HDO4000A High Definition Oscilloscopes HDO6000A High Definition Oscilloscopes HDO8000A High Definition Oscilloscopes / MDA800A Motor Drive Analyzers HDO9000 High Definition Oscilloscopes WaveJet Oscilloscopes Learn More: teledynelecroy.com/probes High Voltage Fiber Optically-isolated Probes - p. 40 - 43 HVFO103

Open the catalog to page 3

Oscilloscope Probes and Probe Accessories - 4

ACTIVE VOLTAGE RAIL PROBE

Open the catalog to page 4

Oscilloscope Probes and Probe Accessories - 5

ACTIVE VOLTAGE RAIL PROBE The RP4030 is designed specifically to probe a 50Ω DC power/voltage rail. The probe has large built-in offset, low attenuation (noise), and high DC input impedance. Built-in offset and low attenuation permit the power/voltage rail to be offset in the oscilloscope by its mean DC voltage with high oscilloscope gain (sensitivity) to achieve a noise-free view of small signal variations. The Teledyne LeCroy Active Voltage Rail Probe Model Numbers: RP4030 high DC input impedance eliminates loading of the DC rail. Opposite page: Active Voltage Rail Probes RP4030 working...

Open the catalog to page 5

Oscilloscope Probes and Probe Accessories - 6

Large Offset Range Permits the DC signal to be displayed in the vertical center of the oscilloscope grid with a high-sensitivity gain setting. Teledyne LeCroy Active Voltage Rail Probe Model Number: RP4030 Key Features 4 GHz Bandwidth ±30V Offset Capability ±800mV Dynamic Range 50 kO DC Input Impedance 1.2x Attenuation (Low Additive Noise, ~5%) MCX terminated cable with wide variety of connections: • Solder-in (4 GHz) • Coaxial Cable to U.FL receptacle (3 GHz) • MCX PCB Mount (4 GHz) • Browser (350 MHz) ProBus Interface Low Attenuation and Noise The probe attenuation is a nominal 1.2x...

Open the catalog to page 6

Oscilloscope Probes and Probe Accessories - 7

4 GHz of Bandwidth Provides maximum bandwidth for probing near the CPU, and the perfect match with the 4 GHz, 10 bit HDO9404 when making power integrity measurements. Wide Assortment of Tips and Leads The RP4030 is supplied standard with solder-in and coaxial cables with MCX and U.FL PCB receptacle mounts. A browser tip is optionally available. Additional receptacles or leads may be purchased as accessories and left connected in circuit for easy connection of different signals during different test or validation stages. Other Oscilloscope Interface Software Requirements Specifications...

Open the catalog to page 7

Oscilloscope Probes and Probe Accessories - 8

ACTIVE VOLTAGE PROBES

Open the catalog to page 8

Oscilloscope Probes and Probe Accessories - 9

ACTIVE VOLTAGE PROBES Engineers must commonly probe high-frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies, but inappropriately load the circuit and distort signals at higher frequencies. Active voltage probes feature both high input R and low input C to reduce circuit loading across the entire probe/oscilloscope bandwidth. With low circuit loading and a form factor that allows probing in confined areas, the active voltage probe becomes Teledyne LeCroy Active Voltage Probe Model Numbers: ZS1000 ZS1500...

Open the catalog to page 9

Oscilloscope Probes and Probe Accessories - 10

ZS SERIES ACTIVE PROBES The ZS Series probes are high impedance, low capacitance active probes that maintain high signal fidelity through 4 GHz. A small form factor and a wide variety of accessories ensures the ZS probe meets every difficult probing challenge. Engineers must commonly probe high frequency signals with high signal fidelity. Typical passive probes with high input R and C provide good response at lower frequencies but inappropriately load the circuit and distort signals at higher frequencies. The ZS Series features both high input R (1 MΩ) and low input C (0.6 pF and 0.9 pF) to...

Open the catalog to page 10

Oscilloscope Probes and Probe Accessories - 11

ZS SERIES ACTIVE PROBES ZS1000 ZS1500 ZS2500 PK-ZS-010 Channel ID Colored Clips PACC-MS005 Freehand Probe Holderk PK-ZS-006 Right Angle Socket PK-ZS-013 Pogo Tip PK-ZS-005 Y-Lead Adapter PK-ZS-004 Single Lead Long PK-ZS-003 Single Lead Short PACC-LD003 Right Angle Pin Lead - 5cm PACC-LD004 Right Angle Lead - Long PACC-CD008 Pogo Ground Lead PK-ZS-008 Ground Blade - Narrow PK-ZS-011 Ground Blade - Wide PK-ZS-007R Microclip Sprung Hook, Red Ordering Information Standard Accessory/Quantity 2.54 mm PCB Adaptor 2.54mm Square Pin Adapter 2.54mm Square Pin Adaptor IC Tip Bent Tip Channel ID Clips...

Open the catalog to page 11

Oscilloscope Probes and Probe Accessories - 12

CURRENT PROBES

Open the catalog to page 12

Oscilloscope Probes and Probe Accessories - 13

Teledyne LeCroy current probes do not require the breaking of a circuit or the insertion of a shunt to make accurate and reliable current measurements. Based on a combination of Hall effect and transformer technology. Teledyne LeCroy current probes are ideal for making accurate AC, DC, and impulse current measurements Wide Range of Applications Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1...

Open the catalog to page 13

Oscilloscope Probes and Probe Accessories - 14

• Autozero and degauss capabilities built into instrument's user interface Teledyne LeCroy Current Probe and Adapter Model Numbers: CP030 CP030A CP031 CP031A CP150 CP500 DCS025 CA10 CP030 — 30 A continuous current rms — 50 A k current peak — 50 MHz bandwidth CP030A — 30 A continuous current rms — 50 A k current peak — 50 MHz bandwidth CP031 CP031A — 30 A continuous current —30 A continuous current —50 Apeak current —50 Apeak current CP150 — 150 A continuous current rms —500 Apeak current — 10 MHz bandwidth CP500 —500 Arms continuous current — 700 A k current peak — 2 MHz bandwidth DCS025 —...

Open the catalog to page 14

Oscilloscope Probes and Probe Accessories - 15

CURRENT PROBES CA10 Current Sensor Adapter The CA10 enables a third-party current measurement device to operate like a Teledyne LeCroy probe. The CA10 is programmable and customizable to work with third-party current measurement devices that output voltage or current signals proportional to measured current. (See page 52 for more information and specifications). Electrical Characteristics* Max. Continuous Input Current Bandwidth Rise Time (typical) Output Voltage_ Max Continuous Input Current at 1 V/A (100mA/div or less) Offset Range at 1V/A (100mA/div or less)_ Minimum Sensitivity_...

Open the catalog to page 15