Rad-icon Product Family Overview Key Features • Large-area, tiled detectors with active area up to 30x30 cm • 5 lp/mm resolution (99µm pixel) • Gigabit Ethernet or CameraLink interface • 14-bit digital video output • Energy range from 10 to 225 kV • Ready-to-run software and drivers Teledyne DALSA’s Rad-icon product family of large-area digital x-ray cameras offers users a high-speed, high-performance x-ray imaging detector with a fast, reliable PC interface (either GigE or CameraLink) for easy integration. The Rad-icon product line leverages Teledyne DALSA’s advanced CMOS image sensing technology, which enables the delivery of low-dose x-ray images and yields higher image quality than a-Si flat panels and image intensifier devices. The cameras in this product line are capable of frame rates up to 30 fps, and communicate via a standard Cat6e or CameraLink data cable over lengths up to 100m.(1) Rad-icon detectors are available with different Gd2O2S (Gadox) scintillator options to address a range of resolution and sensitivity requirements. The camera interface allows easy access to features such as adjusting the frame rate, single and multiple frame acquisitions, and control of advanced timing modes. Each camera ships with user-friendly software tools for stand-alone operation or easy integration with your application software. Camera Options Device Active Area Max. cable length for CameraLink models is 7m. Teledyne Rad-icon Imaging Corporation | 3400 Garrett Drive, Santa Clara, CA 95054 (408) 736-6000 | [email protected] | www.teledynedalsa.c

Specifications Detector Specifications Read noise (rms) Typ. dynamic range Non-linearity (10..90% FS) Typ. readout period Max. frame rate (full res.) Output (pixel) data rate (1) (2) (3) dark current doubles approx. every 8°C ADU = Analog-Digital Unit = 1 LSB (Least Significant Bit) time required to transfer image from sensor to camera memory Camera Specifications Typical supply voltage Supply voltage range Maximum supply current Typical power dissipation Camera interface Trigger connector Gigabit Ethernet or CameraLink TTL General Specifications Operating temperature Storage temperature Humidity...

Resolution & Sensitivity The Rad-icon cameras are designed to work with x-ray sources operating at a wide range of kVp settings. X-ray energies as low as 10-15 keV can be detected. The cameras can be used with x-ray energies as high as 225kV, although we recommend the use of additional shielding and/or collimation at higher energies in order to protect the sensor element and electronics from damage. The pixel spacing of each camera model determines the limiting resolution of the sensor. The actual Modulation Transfer Function (MTF) of the detector depends on the type of scintillator that is installed....

Mechanical Drawing: Rad-icon 1520 36.0 mm M6 mounting hole 6 mm deep (6x) Teledyne Rad-icon Imaging Corporation | 3400 Garrett Drive, Santa Clara, CA 95054 (408) 736-6000 | [email protected] | www.teledynedalsa.com/ndt

Mechanical Drawing: Rad-icon 2022 221 x 204 mm Active Area Teledyne Rad-icon Imaging Corporation | 3400 Garrett Drive, Santa Clara, CA 95054 (408) 736-6000 | [email protected] | www.teledynedalsa.com/ndt

Mechanical Drawing: Rad-icon 3030 306.5 x 306.5 mm Active Area Teledyne Rad-icon Imaging Corporation | 3400 Garrett Drive, Santa Clara, CA 95054 (408) 736-6000 | [email protected] | www.teledynedalsa.com/ndt

I/O Connectors Data Connector: 4-pin LEMO EGG.0B.304(1)/EGG.2B.304(2) TTL (open collector), opto-isolated Pin Pin Pin Pin Trig Trig Trig Trig Ordering Information Rad-icon cameras are available in a single, industrial image quality grade (blemish specification available on request). Specify option -01 for Carestream Min-R® 2190 scintillator, or option -02 for a Mitsubishi Chemical DRZ-Std scintillator. Min-R 2190 not available on the Rad-icon 3030; contact us for additional scintillator options. All cameras ship with a universal input power supply (90-264V, 50-60Hz), power cord, Ethernet cable...