2230-30-3, 2230-30-6, 2230-60-3 High Power, 3-Channel Programmable Power Supplies Datasheet Key Features • Choose from one 195 W model and two 375 W models • 195 W model has two 30 V, 3 A channels and one 5 V, 3 A channel • 375 W models have two 30 V, 6 A channels or two 60 V, 3 A channels and one 5 V, 3 A channel • All channels are independently controlled and are isolated to power a wide range of test setups • All channels have remote sensing so the programmed voltage is accurately applied to the load • Set and monitor output voltages with 0.03% basic accuracy and 1 mV resolution • Monitor load current with 0.1% basic accuracy and 1 mA resolution • Low noise, linear regulation with <1 mV rms ripple and noise • Combine channels in series to output as high as 60 V and in parallel with two or three channels to create capacity as high as 15 A (2230-30-6) The Series 2230 3-channel programmable power supplies provide up to 375 W of power in a space-saving 2U high, half-rack width enclosure to power automotive circuits, LED drivers, power supplies, power ICs, and other highpower circuits. The 2230-30-3 offers 195 W with two 30 V, 3 A channels and a 5 V, 3 A channel. The 2230-30-6 and the 2230-60-3 supplies output as much as 375 W. The 2230-30-6 provides two 30 V, 6 A channels, while the 2230-60-3 has two 60 V, 3 A channels. Both 375 W supplies have a 5 V, 3 A channel as the third channel. These three supplies are linear power supplies; thus, they are low noise supplies to have minimal impact on a device-under-test (DUT). Each channel has a rectangular output characteristic to enable obtaining the full current at the maximum voltage so that the 2230-30-6 can supply 30 V to a 6 A load and the 2230-60-3 can supply 60 V to a 3 A load. • Voltage and current outputs of three channels are displayed simultaneously for immediate observation of each output state • USB and RS-232 interfaces and rear panel connections for automated test convenience Applications Series 2230 power supplies are ideal for testing: • High power analog ICs • Automotive circuits • Telecom infrastructure

Isolated and independent outputs provide maximum flexibility Each output channel of the Series 2230 high power supplies is both independent of the other channels and electrically isolated from the other channels. Therefore, these supplies can power circuits that are optically isolated or transformerisolated from each other and have different reference points. The isolated channels eliminate the need for a second power supply to power one of the isolated circuits. Furthermore, each channel can be independently controlled so that channels can be independently turned on and turned off at any time....

2230-30-3, 2230-30-6, 2230-60-3 High Power, 3-Channel Programmable Power Supplies Deliver accurate voltages to the load The setting and measurement basic voltage accuracy of each channel is 0.03%; and the setting and measurement resolution is 1 mV. Thus, the user can be confident that the programmed output is accurately applied to the output terminals. In addition, using the remote sense leads for each channel ensures that the programmed voltage is applied to the load; the remote sense leads compensate for and overcome the voltage drops due to the resistances in the test leads. Power Supply +...

Save space and minimize test lead length in automated test systems Even though the Series 2230 supplies can output 195 W and 375 W and are linear, low noise sources, they are only 2 U high and half-rack wide. The compact size helps to minimize the size of a test system by saving valuable rack space. In addition, the Series 2230 supplies have both front and rear output connections so that test lead wires from the supplies can be as short as possible. If the rear panel output connections are used, then the test leads are protected from accidental contact to improve test system reliability. 2230G-HRM...

2230-30-3, 2230-30-6, 2230-60-3 High Power, 3-Channel Programmable Power Supplies Specification Conditions Specifications are the standards against which the 2230-30-3, 2230-30-6, and 2230-60-3 are tested. Upon leaving the factory, the 2230-30-3, 2230-30-6, and 2230-60-3 meet these specifications. Typical values are not warranted, apply at 23°C ± 5°C, and are provided solely as useful information. Specifications apply under these conditions: • Temperature 0°C to 40°C and relative humidity 10% to 80% unless defined differently in this document. • After a 30-minute warmup period. • Within one year...

Series Readback Resolution Parallel Setting Resolution Voltage Current Parallel Readback Resolution Rise Time (10% to 90%) Fall Time (90% to 10%) Load Transient Recovery Time Voltage setting band 50 mV, 50% to 100%, 1 kKHz, rise and fall rate 5 A per µs: ≤50 µs (typical) Transition Time CC mode to CV mode, V-set = 5 V, I-limit = 0.5 A, resistive load change from 2.5 Ω to 25 Ω: ≤10 ms CV mode to CC mode, V-set = 5 V, I-limit = 0.5 A, resistive load change from 25 Ω to 2.5 Ω: ≤5 ms Output Timer Setting Range Reso

2230-30-3, 2230-30-6, 2230-60-3 High Power, 3-Channel Programmable Power Supplies General Specifications Communications USB: Type A to B connector, USB 2.0, USBTMC compatible RS232: Baud Rates: 4800/9600/19,200/38,400/57,600/115,200 Rear-Panel Connectors Output: 15-pin terminal block socket USB Device: Type B connector AC Power Input: 3-prong socket assembly with fuse Vacuum fluorescent display Output and Remote Sense Removable 15-15-pin screw-terminal block carries the following signals: Output Channels: Duplicates the front-panel outputs Remote Sense Lines: Connections for remote sense for...

Programmable 3-Channel Power Supply, 195 W, Two 30 V, 3 A Channels, One 5 V, 3 A Channel Programmable 3-Channel Power Supply, 375 W, Two 30 V, 6 A Channels, One 5 V, 3 A Channel Programmable 3-Channel Power Supply, 375 W, Two 60 V, 3 A Channels, One 5 V, 3 A Channel 2230G-HRM Harmonic Reduction Module (for 2230-30-6 and 2230-60-3) Screw Terminal Block, 15 Terminals Power Cord (See Power Cord Options) Traceable Calibration Certificate Three-Year Warranty User Manual, Quick Start Guide, KickStart, LabView and IVI Drivers available on www.tek.com/2230-highpower Power Cord Options A0 North America...