ZEPHYR EC - THE SHOP CLASSIC
20Pages

ZEPHYR ZEPHYR ZEPHYR INDIVIDUAL INNOVATIVE ENERGY-SAVING

intake grille with micro-intake grille behind it sheet steel high-quality powder coated with hidden screws Zephyr EC is the classic model for use in shops. Installationready unit which can be used for many applications, with 4 installation variants. Free-hanging, flush with the ceiling as a cassette, installation in suspended ceilings with sliding supports, and, on request also available as a floor-mounted vertical unit. Self-supporting sheet steel. Screws are not visible. High-quality powder coating, RAL 9016 as standard (traffic white). Other colours are available. Access panel hidden...

+ Made in Germany + ErP 2015 ready / EC fans + Certified by TÜV-Süd + Robust, self-supporting sheet steel + Individual colours available (standard RAL 9016) + 4 installation variants + Individual unit lengths up to 3000 mm + Service friendly thanks to filterless micro-intake grille + Simple to install + Aerodynamically optimised discharge fin + Different heating media possible EC fans The efficiency of the EC fans used by TEKADOOR is > 90% under partial load operation. This is 30–35% higher than for conventional AC fans. This does not just increase the efficiency, but also reduces the...

PHYR DETAILS Achtitog! Attentle! Ahcmbn! Attendant:! Connections Heating connections - flow and return - on top of the unit as standard for easy connection to the on-site heating system. Optionally, the connections can also be located at the side. Connection box (LPHW) Simple electrical connection via connection box (voltage supply 230V/50Hz on the top of the unit); side connections are available as an option. Exception: Electrical units with a heating capacity greater than 22,5 kW.

Data cable connection/interface Simple, standard plug and play connection of the data cable and an optional solenoid valve on the top side of the unit. The connection can be offset on request. Control: Input for the data cable to the control unit. Auxiliary: Output for parallel operation with other units, Discharge fin The shielding performance of the door air curtain system is optimised by adjusting the discharge fin. The fin can be adjusted in 5 stages. During the heating period, the discharge fin should be tilted outwards by 10 to 15 degrees to prevent cold air coming in from the...

INSTALLATION VARIANTS

Free-hanging FRONT VIEW SIDE VIEW BOTTOM VIEW Optional: side connections connection box provision for screw Vorbereitung für connection M mm Verschraubung20 20 circuit board Platine * Attention! Measure will change for model Zephyr LX / LXX from 260 mm to 450 mm and from 460 mm to 715 mm and revetting nut M8 will change to M10. 60 100 A = VARIABLE UNIT LENGTH * WE RESERVE THE RIGHT TO MAKE TECHNICAL CHANGES Connection-ready free-hanging door air curtain unit for visible installation directly above the door. Ambient air intake is at the front, on the room side.

Cassette BOTTOM VIEW SIDE VIEW hidden fixing screw for inspection circuit board Platine Durchführung performance Temperaturfor temperature fühler sensor FRONT VIEW Vorbereiprovision for tung screw Verschrauconnection bung M20 20 mm Re inspection panel vision prepared for using in a suspended ceiling Re inspection panel vision fitting bei units Befestigung nur forüber 2m Geräte M8 Einnietmutter unter der Lasche bigger than 2m verschiebbar movable 9 mm Langloch 9 mm long hole für Befestigung A = VARIABLE UNIT LENGTH * WE RESERVE THE RIGHT TO MAKE TECHNICAL CHANGES Connection-ready door air...

Suspended ceiling unit FRONT VIEW provision for für Vorbereitung screw VerschraubungM20 mm connection 20 circuit board Platine Optional: side connection BOTTOM VIEW * Attention! Measure will change for model A = VARIABLE UNIT LENGTH Zephyr LX / LXX from 260 mm to 580 mm and from 720 mm to 1100 mm and revetting nut M8 will change to M10. * WE RESERVE THE RIGHT TO MAKE TECHNICAL CHANGES Connection-ready door air curtain unit with integrated intake chamber on the underside. Intake and discharge sliding supports for installation in a suspended ceiling. Only the intake and discharge grilles are...

STANDARD CIRCUIT DIAGRAM FOR LPHW (PUMPED WARM WATER) interface (optional) Stufe MODE Standard Anschlusskabel (20 m) mit RJ-45 Stecker Magnetventil (OPTIONAL) zum Steuerteil (CONTROL) Adresse 1-9 zum Steuerteil (CONTROL) Adresse 1-9 Standard Anschlusskabel (20 m) mit RJ-45 Stecker Magnetventil (OPTIONAL) Betrieb pot.-frei Störung pot.-frei nicht belegt nicht belegt Erdung, Nullung oder Schutzschaltung nach Adress Schalter 0 = MASTER 1 - 9 = SLAVE Technische Änderungen vorbehalten * WE RESERVE THE RIGHT TO MAKE TECHNICAL CHANGES nicht belegt GTM 2 EC control unit with optional ModBus...

CIRCUIT DIAGRAM FOR ELECTRICAL HEAT EXCHANGER interface (optional) Room thermostat Standard supplied shielded datacable (20 m) 1:1 straight wired RJ-45 Stecker zum Steuerteil (CONTROL) Adresse 1-9 Adress switch 0 = MASTER 1 - 9 = SLAVE Adress Schalter 0 = MASTER 1 - 9 = SLAVE Technical changes reserved Datum 01.08.2014 Maßstab * WE RESERVE THE RIGHT TO MAKE TECHNICAL CHANGES Gruppe Erstelldatum nicht belegt Benennung Name GTM 1 E EC control unit with optional ModBus interface 2 languages I Ebe selected (German/English), menu-prompted electronic standard control GTM can EC UK 140801 for air...

OPTIONAL ACCESSORIES Thermostatic straightway valve Door contact solenoid switch (Setting range + 25 °C to + 45 °C) limits the discharge temperature (constant supply air temperature limitation). Also available as a 3-way valve. For problem-free, vibration-free ceiling attachment, consisting of M8 or M10 threaded rods, up to 1000 mm length, vibration dampers, turnbuckles and counter nuts. In automatic mode switches on the door air curtain in the preselected stage – in conjunction with GTM 2 EC, GTM 3 EC and GTM 2 E EC.

Frost protection Solenoid valve thermostat Room thermo stat Thermo-electric shut-off valve For monitoring LPHW heat exchangers exposed to the risk of frost. As soon as the temperature falls below +7 °C the fans are switched off and an optional solenoid valve is opened. Opens or closes the warm water circuit in the summer/winter setting of the control unit, in order to close the heating water circuit and save energy during summer operation or when the air curtain is not working (normally closed). Caution: If solenoid valves are used, it is expressly recommended to install a frost protection...