Catalog excerpts
TECNOLOGIE SPECIALI APPLICATE Pneumatic motors Characteristics of pneumatic motors
Open the catalog to page 1TECNOLOGIE SPECIALI APPLICATE INDICE TSA Special technologies applied Characteristics of pneumatic motors POWER SPEED SPEED TORQUE AT MAXIMUM SPEED STARTING TORQUE STALL TORQUE WAYS Of CHANGING THE MOTOR’S PERFORMANCE PRESSURE REGULATING FLOW REGULATING INLET AIR CONDITIONS CONSUMPTION AIR QUALITY Pneumatic diagram (power – motor control) PNEUMATIC ACCESSORIES MANUAL OR PNEUMATIC CONTROL VALVES DISSOLATOR / SILENCER FILTER Characteristics of pneumatic motors
Open the catalog to page 3Special applied technologies TSA founded in 1984, for over 30 years has been designing, manufacturing and distributing pneumatic motors, articulated arms for torque reaction, assembling systems and special equipment. Its technical design office is in charge of studying all of the required characteristics to guarantee maximum reliability and high productivity, according to modern ergonomic principles. Product quality and safety are now a consolidated standard for TSA. Just-in-time deliveries, a wide, flexible range of products, including diversified motors and arms, an efficient spare parts...
Open the catalog to page 4TECNOLOGIE SPECIALI APPLICATE Characteristics of pneumatic motors The outlet power of a pneumatic motor varies depending on its speed and torque. The performance levels of a pneumatic motor depend on the inlet air pressure level measured at the entry point in the motor; this means that it is sufficient to regulate the incoming air to substantially change the torque and speed values in a pneumatic motor. The choice of a pneumatic motor is based on three fundamental parameters: POWER, SPEED and TORQUE. POWER Pneumatic motors produce a characteristic power curve whose maximum value is obtained...
Open the catalog to page 5WAYS Of CHANGING THE MOTOR’S PERFORMANCE The speed and torque in a pneumatic motor can be adjusted by regulating the pressure or throttling the air flow. PRESSURE REGULATING The speed and power can also be reduced by installing a pressure regulator. A pressure regulator, always connected on the entry hole, keeps the inlet air pressure to the motor in check. A pressure regulating system affects the output torque on the shaft, thus making it easier to control the starting torque. If the speed and torque need to be controlled, the best configuration consists in a pressure regulator to the...
Open the catalog to page 6TECNOLOGIE SPECIALI APPLICATE Pneumatic diagram (power – motor control) A = Filter B = Regulator of pressure C = Lubricator D = Silencer E = 3/2 valve F = Engine G = Valve 5/3 Non-reversible motor operation with 3/2 valve A Non-reversible motor operation with 5/3 closed-center valve Characteristics of pneumatic motors
Open the catalog to page 7PNEUMATIC ACCESSORIES TSA offers a pneumatic component programme for air treatment and control of pneumatic motors on premium brands, including SMC, BOSCH, NORGREN, WILKERSON. This programme consists of air treatment units, valves and silencers. The available connections range from G1/4” to G2”. AIR TREATMENT UNITS All of the filters used have automated condensation discharge, the FRL units are installation-ready and fitted with a pressure gauge. Models Max. operating temperature Standard filtration rate Flow rate in l/sec
Open the catalog to page 8TECNOLOGIE SPECIALI APPLICATE MANUAL OR PNEUMATIC CONTROL VALVES Easy and quick to install, the default valves fitted on TSA pneumatic motors are 5-way 3-position valves with centres open in idle position, with lever or pneumatic control. Models Aria filtrata e lubrificata Flow rate at 6 bar with Δ p = 1 Nl / min Minimum pilot pressure Pilot connection
Open the catalog to page 9SILENCERS All motors are fitted with a threaded exhaust gate, which makes it possible to add a silencer in order to reduce the noise level. It is also possible to add another hose between exhaust and silencer which will further reduce the noise level. Models Operating temperature
Open the catalog to page 10TECNOLOGIE SPECIALI APPLICATE DISSOLATOR / SILENCER FILTER Models Bath capacity Operating temperature Sound reduction Construction materials Threaded cover Filter element Primary Secondary borosilicate cloth PVC fiber Sleeve support Characteristics of pneumatic motors
Open the catalog to page 11Pneumatic motors Telescopic booms Articulated booms
Open the catalog to page 12TECNOLOGIE SPECIALI APPLICATE Characteristics of pneumatic motors
Open the catalog to page 13TECNOLOGIE SPECIALI APPLICATE Tecnologie Speciali Applicate Srl | Via Calari 16,40069 | Zola Predona BOLOGNA | Tel. (+39) 051 590900 Fax. (+39) 051 592293 E-mail: tsa@tsabologna.com - www.tsabologna.com
Open the catalog to page 14All Tecnologie Speciali Applicate catalogs and technical brochures
-
SWINGING DEVICE
1 Pages
-
WRIST ACCESSORIES
1 Pages
-
TOOL SUPPORT CLAMP
1 Pages
-
PNEUMATIC BRAKES
1 Pages
-
VERTICAL TELESCOPIC ARMS
28 Pages